PIAGGIO Liberty 50 Catalyzed Скачать руководство пользователя страница 87

Страница: 87 / 165

- Keeping the half crankcase on the transmission

side, insert the flywheel side half crankcase with a

clean precise movement

- Insert at least three clamping screws and tighten

up rapidly

- Insert the other 5 screws and tighten them to the

specified torque.

Locking torques (N*m)

crankcase coupling screws

11 - 13

- Move the crankcase separation plate in a position

back from the one indicated in the figure

- Install the special magnetic support with dial

gauge at the end of the crankshaft

- Check the axial clearance of the crankcase

If this is not within the maximum limit allowed, re-

peat the crankcase coupling procedure

Specific tooling

020335Y

Magnetic mounting for dial gauge

Characteristic

Axial clearance with warm crankcase

0.10 ÷ 0.12 mm

Axial clearance with cold crankcase

0.06 to 0.08 mm

Limit value with cold crankcase

0.02 ÷ 0.03 mm

Lubrication

Crankshaft oil seals

Liberty 50 Catalyzed

Engine

ENG - 87

Содержание Liberty 50 Catalyzed






































































































































































Результаты поиска

Содержание Liberty 50 Catalyzed

Отзывы:

Бренды по названию

Популярные бренды

PIAGGIO Liberty 50 Catalyzed, Руководство по ремонту

Результаты поиска

Содержание Liberty 50 Catalyzed

Отзывы:

Бренды по названию

Популярные бренды