PIAGGIO Liberty 50 Catalyzed Скачать руководство пользователя страница 72

Страница: 72 / 165

- Remove the bearing off the driven pulley shaft

using the specific tool and a press

N.B.

USE THE SPECIFIC TOOL ON THE SIDE WITH THE SMALL-
ER INTERNAL DIAMETER

Specific tooling

020452Y

Tube for removing and refitting the

driven pulley shaft

Inspecting the hub shaft

- Check the three shafts for wear or distortion of

the toothed surfaces, the bearing housings, and

the oil seal housings.

- If faults are found, replace the damaged compo-

nents.

- Check capacity ( A ) of the transmission gear

(wear, deformations, etc.)

- Check the pulley shaft seating: Superficial wear

( B ) may indicate irregularities in the crankcase

seatings or in the pulley shaft capacities

Inspecting the hub cover

- Check that the fitting surface is not dented or dis-

torted.

- If faults are found, replace the hub cover.

Engine

Liberty 50 Catalyzed

ENG - 72

Содержание Liberty 50 Catalyzed






































































































































































Результаты поиска

Содержание Liberty 50 Catalyzed

Отзывы:

Бренды по названию

Популярные бренды

PIAGGIO Liberty 50 Catalyzed, Руководство по ремонту

Результаты поиска

Содержание Liberty 50 Catalyzed

Отзывы:

Бренды по названию

Популярные бренды