PIAGGIO Liberty 50 Catalyzed Скачать руководство пользователя страница 86

Страница: 86 / 165

- Firmly insert the crankshaft until the bearing rea-

ches the end-of-stroke stop

- Let the temperature of the half crankcase settle

at the temperature of the crankshaft.

- Again install the special crankcase separation

plate

NOT

installing the crankshaft protection

- During the assembly phase keep the central

thrust screw loose.

- Take the four clamping screws to the end of the

stroke and loosen them again with the same angle

(e.g. 90°)

- When the temperature has settled, preload the

thrust screw of the tool manually until the ball bear-

ing clearance is cancelled out.

Specific tooling

020163Y

Crankcase splitting plate

Refitting the crankcase halves

- Prepare the coupling surface with LOCTITE 510

applying a thin layer of it after degreasing the sur-

face using a suitable solvent (e.g. trichloroethy-

lene)

- Heat the flywheel-side half crankcase with a ther-

mal gun.

Recommended products

Loctite 510

Liquid sealant

Gasket

Engine

Liberty 50 Catalyzed

ENG - 86

Содержание Liberty 50 Catalyzed






































































































































































Результаты поиска

Содержание Liberty 50 Catalyzed

Отзывы:

Бренды по названию

Популярные бренды

PIAGGIO Liberty 50 Catalyzed, Руководство по ремонту

Результаты поиска

Содержание Liberty 50 Catalyzed

Отзывы:

Бренды по названию

Популярные бренды