PIAGGIO Liberty 50 Catalyzed Скачать руководство пользователя страница 7

Страница: 7 / 165

Rules

This section describes general safety rules for any maintenance operations performed on the vehicle.

Safety rules

- If work can only be done on the vehicle with the engine running, make sure that the premises are well

ventilated, using special extractors if necessary; never let the engine run in an enclosed area. Exhaust

fumes are toxic.

- The battery electrolyte contains sulphuric acid. Protect your eyes, clothes and skin. Sulphuric acid is

highly corrosive; in the event of contact with your eyes or skin, rinse thoroughly with abundant water

and seek immediate medical attention.

- The battery produces hydrogen, a gas that can be highly explosive. Do not smoke and avoid sparks

or flames near the battery, especially when charging it.

- Fuel is highly flammable and it can be explosive given some conditions. Do not smoke in the working

area, and avoid naked flames or sparks.

- Clean the brake pads in a well-ventilated area, directing the jet of compressed air in such a way that

you do not breathe in the dust produced by the wear of the friction material. Even though the latter

contains no asbestos, inhaling dust is harmful.

Maintenance rules

- Use original PIAGGIO spare parts and lubricants recommended by the Manufacturer. Non-original or

non-conforming spares may damage the vehicle.

- Use only the appropriate tools designed for this vehicle.

- Always use new gaskets, sealing rings and split pins upon refitting.

- After removal, clean the components using non-flammable or low flash-point solvents. Lubricate all

the work surfaces, except tapered couplings, before refitting these parts.

- After refitting, make sure that all the components have been installed correctly and work properly.

- Use only equipment with metric sizes for removal, service and reassembly operations. Metric bolts,

nuts and screws are not interchangeable with coupling members using English measurements. Using

unsuitable coupling members and tools may damage the vehicle.

- When carrying out maintenance operations on the vehicle that involve the electrical system, make

sure the electrical connections have been made properly, particularly the ground and battery connec-

tions.

Liberty 50 Catalyzed

Characteristics

CHAR - 7

Содержание Liberty 50 Catalyzed






































































































































































Результаты поиска

Содержание Liberty 50 Catalyzed

Отзывы:

Бренды по названию

Популярные бренды

PIAGGIO Liberty 50 Catalyzed, Руководство по ремонту

Результаты поиска

Содержание Liberty 50 Catalyzed

Отзывы:

Бренды по названию

Популярные бренды