PIAGGIO Liberty 50 Catalyzed Скачать руководство пользователя страница 110

Страница: 110 / 165

Headlight assy.

• Remove the front handlebar cover.

• Unscrew the 4 fixing screws and remove the

headlight assembly.

N.B.

N.B. TO REPLACE THE HIGH/LOWBEAM HEADLIGHT
BULB, REMOVE THE RUBBER COVER AND TURN THE
SUPPORTING PLATE BY 30° ANTICLOCKWISE. TO RE-
PLACE THE SIDE LIGHT BULB, JUST SLIDE IT OFF THE
RUBBER BULB HOLDER.

See also

Front handlebar cover

Frame central cover

• Remove the rear luggage rack

• Remove the saddle

• Remove the spark plug access cover, unscrew

the 2 screws joining the helmet compartment

clamp with the footrest.

• Unscrew the 2 side screws placed on the bumper rings.

• Remove the cover by holding it from the rear part and disconnect the turn indicator light connections

See also

Seat
Rear rack

Chassis

Liberty 50 Catalyzed

CHAS - 110

Содержание Liberty 50 Catalyzed






































































































































































Результаты поиска

Содержание Liberty 50 Catalyzed

Отзывы:

Бренды по названию

Популярные бренды

PIAGGIO Liberty 50 Catalyzed, Руководство по ремонту

Результаты поиска

Содержание Liberty 50 Catalyzed

Отзывы:

Бренды по названию

Популярные бренды