PIAGGIO Liberty 50 Catalyzed Скачать руководство пользователя страница 66

Страница: 66 / 165

Refitting the driven half-pulley bearing

- Fit a new ball bearing with the specific tool.

- Fit the ball bearing retention snap ring.

- Fit the new roller bearing with the wording visible

from the outside.

CAUTION

PROPERLY SUPPORT THE HALF-PULLEY TO PREVENT
DAMAGE TO THE THREADED END WHILE THE BEARINGS
ARE BEING FITTED.

Specific tooling

020376Y

Adaptor handle

020456Y

Ø 24 mm adaptor

020362Y

12 mm guide

020171Y

Punch for Ø 17 mm roller case

Inspecting the clutch spring

- Check that the contrast spring of the driven pulley

does not show signs of deformation

- Measure the free length of the spring

Characteristic

Standard length

118 mm

Minimum length allowed after use

XXXX

Refitting the clutch

- Preassemble the driven pulley group with spring,

sheath and clutch.

- Position the spring with the sheath

- Insert the components in the tool and preload the

spring being careful not to damage the plastic

sheath and the end of the threaded bar.

Engine

Liberty 50 Catalyzed

ENG - 66

Содержание Liberty 50 Catalyzed






































































































































































Результаты поиска

Содержание Liberty 50 Catalyzed

Отзывы:

Бренды по названию

Популярные бренды

PIAGGIO Liberty 50 Catalyzed, Руководство по ремонту

Результаты поиска

Содержание Liberty 50 Catalyzed

Отзывы:

Бренды по названию

Популярные бренды