Phoenix Contact Axioline F Скачать руководство пользователя страница 6

Страница: 6 / 86

AXL F PSDO8/3 1F

PHOENIX CONTACT

105739_en_04

Assembly, removal, and electrical installation........................................................................... 27

4.1

Assembly and removal ........................................................................................ 27

4.1.1

Unpacking the module ......................................................................... 27

4.1.2

Preparation and assembly ................................................................... 27

4.1.3

Setting the DIP switch .......................................................................... 28

4.1.4

Mounting and removing the module ..................................................... 29

4.2

Electrical installation ............................................................................................ 31

4.2.1

Electrical installation of the Axioline F station ....................................... 31

4.2.2

Electrical installation of the module ...................................................... 31

Parameterization of the module ................................................................................................ 33

5.1

Setting the F-Parameters and i-Parameters......................................................... 33

5.2

Parameterization of the safe outputs ................................................................... 34

5.3

Behavior of the outputs in the event of enabled switch-off delay

for stop category 1 ............................................................................................... 35

Connection examples for safe outputs...................................................................................... 37

6.1

Explanation of the examples................................................................................ 37

6.2

Notes on the protective circuit of external relays/contactors

(freewheeling circuit) .......................................................................................... 38

6.3

Measures to achieve a specific safety integrity.................................................... 39

6.4

Single-channel assignment of safe outputs ......................................................... 40

6.5

Two-channel assignment of safe outputs ............................................................ 43

Startup and validation ............................................................................................................... 47

7.1

Initial startup ........................................................................................................ 47

7.1.1

Startup mode ....................................................................................... 48

7.2

Restart after replacing a module .......................................................................... 49

7.2.1

Replacing a module ............................................................................. 49

7.2.2

Restart ................................................................................................. 49

7.3

Validation............................................................................................................. 49

Errors: messages and removal ................................................................................................. 51

8.1

Reading diagnostic messages............................................................................. 51

8.1.1

DiagState object 0x0018 ...................................................................... 53

8.1.2

DiagStateChannelNo object 0x0033 .................................................... 53

8.1.3

DiagStateAddValue object 0x0034 ...................................................... 54

8.1.4

ResetDiag object 0x0019 ..................................................................... 54

8.1.5

Examples for reading a diagnostic message ........................................ 55

Содержание Axioline F























































































Результаты поиска

Содержание Axioline F

Отзывы:

Бренды по названию

Популярные бренды

Phoenix Contact Axioline F, Руководство пользователя

Результаты поиска

Содержание Axioline F

Отзывы:

Бренды по названию

Популярные бренды