Phoenix Contact Axioline F Скачать руководство пользователя страница 79

Страница: 79 / 86

Appendix: checklists

105739_en_04

PHOENIX CONTACT

D Appendix:

checklists

The checklists listed in this section provide support when carrying out the following tasks on

the AXL F PSDO8/3 1F module: planning, assembly and electrical installation, startup,

parameterization, and validation.

Archive the completed checklists to use as reference for recurring tests.

The checklists do not replace the validation, initial startup, and regular testing performed by

qualified personnel.

The following section of a checklist shows an example of a completed checklist.

These checklists may be used as planning documentation and/or as verification to ensure

the steps in the specified phases are carried out carefully.

Checklist ...

Device type/equipment identification

AXL F PSDO8/3 1F / BK20NA10

Version: HW/FW

00/101

Date

2008-01-03

Test engineer 1

John Smith

Test engineer 2

Jane Brown

Comment

System XXX has been checked for engine hood production

No. Requirement (mandatory)

Yes

Comment

. . .

No. Requirement (optional)

Yes

Comment

. . .

Key:

Equipment identification

Enter the device type and/or the equipment identification for the relevant module.

Version: HW/FW

Enter the hardware and firmware version of the module: Section “Structure of the module”

on page 14.

Date

Enter the date on which you began to fill in this checklist.

Editor

Enter the name of the editor.

Test engineer

Enter the name of the test engineer.

Comment

Where necessary, enter a comment.

Requirement (mandatory)

These requirements must be met for a safety application, in order to complete the relevant

phase using the checklist.

Requirement (optional)

These requirements are optional. For points that are not met, please enter an appropriate

comment in the relevant field.

Содержание Axioline F























































































Результаты поиска

Содержание Axioline F

Отзывы:

Бренды по названию

Популярные бренды

Phoenix Contact Axioline F, Руководство пользователя

Результаты поиска

Содержание Axioline F

Отзывы:

Бренды по названию

Популярные бренды