manualshive.com logo in svg

Phoenix Contact Axioline F, Руководство пользователя

Поделиться
Скачать
Phoenix Contact Axioline F Скачать руководство пользователя страница 43

Connection examples for safe outputs

105739_en_04

PHOENIX CONTACT

43

6.5

Two-channel assignment of safe outputs

For two-channel assignment of the safe outputs, two adjacent outputs of the same 

connector are used. This assignment cannot be parameterized: see “Two-channel” on 

page 34.

Figure 6-3

Two-channel assignment of outputs

K1 (R) and K2 (R) represent the force-guided N/C contacts for monitoring the state of the 

relay (readback contacts). 

•

Connect these contacts via safe digital inputs. 

•

Evaluate the readback and therefore the state of the switching elements in the safe 

application program.

The failure detection time does not have to be taken into consideration for two-channel 

assignment.

Basic specifications

73420006

K2 (R)

K1 (R)

K1

K2

OUT1_Ch1

GND

M

OUT1_Ch2

GND

WARNING: Loss of safety function

Parasitic voltages can result in the loss of the safety function.

•

Connect the actuator ground to the ground terminal point of the corresponding output 

on the Axioline F connector. An external ground may not be used.

Actuator

Two-channel

Achievable 

SIL/SILCL/Cat./PL

SIL 3/SILCL 3/Cat. 4/PL e

Enable the test pulses to improve device diagnostics and for long off times.

Содержание Axioline F























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды