Phoenix Contact Axioline F Скачать руководство пользователя страница 61

Страница: 61 / 86

Errors: messages and removal

105739_en_04

PHOENIX CONTACT

8.3

PROFIsafe errors

The following errors can also occur:

–

PROFIsafe system errors: see Section B 3 “Diagnostic messages for parameter errors

for PROFIsafe” on page 75.

–

PROFIBUS or PROFINET system errors. For information on these errors, refer to the

documentation for the system used.

8.4

Acknowledging an error for PROFIsafe

•

Remove the cause of the error.

•

Acknowledge the diagnostic message.

Parameterization errors cannot be acknowledged. In this case, proceed as follows:

•

Check the parameterization.

•

Adapt the parameterization.

•

Download the new data record.

For instructions on error acknowledgment, refer to the documentation for the controller

used.

WARNING: Hazardous machine state/unintentional machine startup

With the exception of a few special cases, the acknowledgment of an error can result in a

hazardous state as well as unintentional machine startup since the safe outputs are

immediately returned to the operating state.

•

Before acknowledging an error you must make sure that the acknowledgment will not

cause the machine to switch to a hazardous state.

•

When planning the machine or system, make sure that acknowledgment is only

possible if the danger zone is visible.

WARNING: Unintentional machine startup

Startup/restart following power up and when there is no longer a demand of the safety

function can result in unintentional machine startup.

•

Please note that:

–

The module starts up once the configuration and parameterization data record

has been downloaded successfully and internal testing has been completed

without errors.

–

A safety-related input is automatically reset to “1” when the safety function trigger

is reset.

•

If you do not want the machine to restart automatically, configure the safety logic

accordingly.

Содержание Axioline F























































































Результаты поиска

Содержание Axioline F

Отзывы:

Бренды по названию

Популярные бренды

Phoenix Contact Axioline F, Руководство пользователя

Результаты поиска

Содержание Axioline F

Отзывы:

Бренды по названию

Популярные бренды