manualshive.com logo in svg

Phoenix Contact Axioline F, Руководство пользователя

Поделиться
Скачать
Phoenix Contact Axioline F Скачать руководство пользователя страница 82

AXL F PSDO8/3 1F

82

PHOENIX CONTACT

105739_en_04

D 3

Startup and parameterization

Checklist for startup and parameterization of the module

Device type/equipment identification

Version: HW/FW

Date

Editor

Test engineer 

Comment

No. Requirement (mandatory)

Yes

Comment

1

Was startup completed according to the specifications (specifications 

from the planning phase or according to the user manual)?

2

During startup, is it ensured that any person starting hazardous 

movements intentionally can only do so with a direct view of the danger 

zone?

3

Are all parameters parameterized for the outputs and is the 

F_WD_Time set correctly?

4

For outputs that are parameterized for two-channel operation, are both 

channels parameterized correctly for each other?

5

Are the output test pulses parameterized according to the actuator to 

be connected?

6

Has the switch-off delay for stop category 1 been observed in the 

calculation of the total response time for the machine/system?

No. Requirement (optional)

Yes

No

Comment

7

Have safety distances that must be observed been calculated 

according to the response and delay times implemented?

Date

Signature (editor)

Date

Signature (test engineer)

Содержание Axioline F























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды