Phoenix Contact Axioline F Скачать руководство пользователя страница 31

Страница: 31 / 86

Assembly, removal, and electrical installation

105739_en_04

PHOENIX CONTACT

4.2

Electrical installation

4.2.1

Electrical installation of the Axioline F station

Electrical installation of the Axioline F station includes the following:

–

Connection to the higher-level bus system

–

Connecting the supply voltages for the Axioline F station

•

Carry out electrical installation for the Axioline F station according to the following user

manuals:

–

Axioline F: system and installation user manual, UM EN AXL F SYS INST

–

Axioline F system manual for your bus system

•

Observe the additional information in the documentation for the bus coupler.

4.2.2

Electrical installation of the module

The supply voltage for the module electronics is fed to the bus coupler. From this, the supply

voltage of the module logic is provided via the bus base module. The supply voltage of the

output circuits is fed directly to the module.

The actuators are connected via Axioline F connectors.

•

Wire the connectors according to your application: see Section 3.4 “Terminal point

assignment” on page 25.

WARNING: Electric shock/unintentional machine startup

Make sure that the power to the system is disconnected before carrying out installation

work as this could cause a hazardous electric shock as well as unintentional machine

startup.

•

Prior to installation work, disconnect the power to the system and make sure that it

cannot be switched on again unintentionally.

•

Make sure all work is completed before switching the power back on and that neither

the station nor the system poses a hazard.

Observe the diagnostics indicators and any diagnostic messages.

Observe the general safety notes: see Section 1.2 “Electrical safety” on page 10.

WARNING: Loss of safety function/damage to equipment

Improper installation, e.g., due to the mismatching or polarity reversal of connections, can

result in the loss of the safety function as well as damage to equipment.

•

Take measures to prevent the mismatching or polarity reversal of connections.

•

Prevent the tampering of connections.

Содержание Axioline F























































































Результаты поиска

Содержание Axioline F

Отзывы:

Бренды по названию

Популярные бренды

Phoenix Contact Axioline F, Руководство пользователя

Результаты поиска

Содержание Axioline F

Отзывы:

Бренды по названию

Популярные бренды