Phoenix Contact Axioline F Скачать руководство пользователя страница 10

Страница: 10 / 86

AXL F PSDO8/3 1F

PHOENIX CONTACT

105739_en_04

Do not carry out

any repairs or

modifications

It is prohibited for the user to carry out repair work or make modifications to the module. The

housing must not be opened. The module is protected against tampering by means of

security labels. The security label is damaged in the event of unauthorized repairs or

opening of the housing. In this case, the correct operation of the safety module can no

longer be ensured.

In the event of an error, send the module to Phoenix Contact or contact Phoenix Contact

immediately and engage a service engineer.

Mismatching and polarity

reversal of connections

Take care to avoid the mismatching, polarity reversal or tampering of connections. For

increased protection against mismatching, connectors and slot markings are color coded.

1.2

Electrical safety

Direct/indirect contact

Protection against direct and indirect contact according to VDE 0100 Part 410 must be

ensured for all components connected to the system. In the event of an error, parasitic

voltages must not occur (single-fault tolerance).

Measures required:

–

Using power supply units with safe isolation (PELV).

–

Decoupling circuits, which are not PELV systems, using optocouplers, relays, and other

components which meet the requirements of safe isolation.

Power supply units for

24 V supply

Only use power supply units with safe isolation and PELV according to EN 50178/VDE 0160

(PELV). These power supply units prevent short circuits between the primary and

secondary side.

Make sure that the output voltage of the power supply does not exceed 32 V even in the

event of an error.

Insulation rating

When selecting the equipment, please take into consideration the dirt and surge voltages

which may occur during operation.

The module is designed for overvoltage category II (according to DIN EN 60664-1). If you

expect surge voltages in the system, which exceed the values defined in overvoltage

category II, implement additional measures for voltage limitation.

WARNING: Loss of safety function/hazardous shock currents

Incorrect installation can result in the loss of the safety function as well as hazardous shock

currents.

•

Observe the notes on electrical safety.

•

Plan the modules used and their installation in the system according to the specific

requirements.

•

Recheck plants and systems retrofitted with PROFIsafe.

Содержание Axioline F























































































Результаты поиска

Содержание Axioline F

Отзывы:

Phoenix Contact Axioline F, Руководство пользователя, Страница: 10 / 86

Результаты поиска

Содержание Axioline F

Отзывы: