Phoenix Contact Axioline F Скачать руководство пользователя страница 48

Страница: 48 / 86

AXL F PSDO8/3 1F

PHOENIX CONTACT

105739_en_04

7.1.1

Startup mode

The device features a startup mode in which the software can be used to perform

the following functions:

–

Wiring check

–

Set outputs

–

Read and acknowledge diagnostic messages

Startup mode is set using the DIP switch on the top of the module, see Section 4.1.3 “Setting

the DIP switch” on page 28.

To enter startup mode, proceed as follows:

Set position 11 of the DIP switch to “on”.

Carry out a power up.

The red CM LED indicates that the device is in startup mode.

In the software, enter the address set on the device.

WARNING: Risk due to standard operation

The module is

not

safe in startup mode, as all partial safety functions are deactivated.

Unintentional system states or incorrect responses cannot be ruled out.

•

Do not enter any danger zones and make sure that no other persons can access the

danger zone either.

WARNING: Risk due to unexpected machine startup

Unexpected machine startup can occur as a result of standard operation in startup mode.

•

Take the standard behavior of the device in startup mode into consideration as early

as the planning phase.

•

Take appropriate safety precautions.

For additional information on the software, refer to the documentation for the

software.

The software can be downloaded free of charge at

phoenixcontact.net/products

Содержание Axioline F























































































Результаты поиска

Содержание Axioline F

Отзывы:

Бренды по названию

Популярные бренды

Phoenix Contact Axioline F, Руководство пользователя

Результаты поиска

Содержание Axioline F

Отзывы:

Бренды по названию

Популярные бренды