Phoenix Contact Axioline F Скачать руководство пользователя страница 51

Страница: 51 / 86

Errors: messages and removal

105739_en_04

PHOENIX CONTACT

Errors: messages and removal

Depending on the error type, errors that are diagnosed are displayed via the local

diagnostics indicators and/or transmitted to the controller as diagnostic messages.

8.1

Reading diagnostic messages

Diagnostic messages are read via communication objects. For additional information on

communication objects and general Axioline F error messages, please refer to the following

user manuals:

Documentation

–

Axioline F: system and installation, UM EN AXL F SYS INST

–

Axioline F: diagnostic registers and error messages, UM EN AXL F SYS DIAG

Error code

The error code is specified for all diagnostic messages via the “Code” component of

DiagState object 0x0018, subindex 4. Description of possible error codes: see Section 8.2

“Error codes” on page 56.

Error location

The error location is indicated for all diagnostic messages via the “Channel/Group/Module”

component of DiagState object 0x0018, subindex 3 or via DiagStateChannelNo object

0x0033.

The error location indicated via the “Channel/Group/Module” component corresponds to

the terminal point of output 00 to 07, see Table 3-2 and Table 3-3.

Example:

In the event of a short circuit at terminal point 05 of output OUT2_CH2, value 0x05 is

indicated in DiagState object 0x0018, subindex 3. The error is located in the “Channel 5”

diagnostics.

Channel number 255 (0xFF) means that the entire module is affected.

Table 8-1

Assignment of the outputs to the diagnostic message

Terminal point

Output

OUT0

OUT1

OUT2

OUT3

OUT0_CH1

OUT0_CH2

OUT1_CH1

OUT1_CH2

OUT2_CH1

OUT2_CH2

OUT3_CH1

OUT3_CH2

“Channel”

diagnostics

Содержание Axioline F























































































Результаты поиска

Содержание Axioline F

Отзывы:

Phoenix Contact Axioline F, Руководство пользователя, Страница: 51 / 86

Результаты поиска

Содержание Axioline F

Отзывы: