Phoenix Contact Axioline F Скачать руководство пользователя страница 56

Страница: 56 / 86

AXL F PSDO8/3 1F

PHOENIX CONTACT

105739_en_04

8.2

Error codes

Module replacement

following an error

If you replace the module in the event of an error, refer to the following sections: see

Section 4 “Assembly, removal, and electrical installation” on page 27, see Section 7.2

“Restart after replacing a module” on page 49.

LED

The “LED” column specifies which local diagnostics LED indicates the error.

Acknowledgment and

restart

For every error that occurs, first remove the cause of the error. If necessary, acknowledge

the error. The “Acknowledgment/remedy” column specifies whether an error must be

acknowledged and which special conditions apply for re-enabling an input or the module.

Please contact Phoenix Contact if error codes are indicated by the system which do not

appear in:

–

The tables below in this user manual

–

The Axioline F: system and installation user manual, UM EN AXL F SYS INST

–

The Axioline F: diagnostic registers and error messages user manual,

UM EN AXL F SYS DIAG

WARNING: Hazardous machine state/unintentional machine startup

With the exception of a few special cases, the acknowledgment of an error can result in a

hazardous state as well as unintentional machine startup since the safe output is

immediately returned to the operating state.

•

Before acknowledging an error you must make sure that the acknowledgment will not

cause the machine to switch to a hazardous state.

•

When planning the machine or system, make sure that acknowledgment is only

possible if the danger zone is visible.

WARNING: Unintentional machine startup

Startup/restart following power up and when there is no longer a demand of the safety

function can result in unintentional machine startup.

•

Please note that:

–

The module starts up once the configuration and parameterization data record

has been downloaded successfully and internal testing has been completed

without errors.

–

A safety-related input is automatically reset to “1” when the safety function trigger

is reset.

•

If you do not want the machine to restart automatically, configure the safety logic

accordingly.

Содержание Axioline F























































































Результаты поиска

Содержание Axioline F

Отзывы:

Phoenix Contact Axioline F, Руководство пользователя, Страница: 56 / 86

Результаты поиска

Содержание Axioline F

Отзывы: