Phoenix Contact Axioline F Скачать руководство пользователя страница 35

Страница: 35 / 86

Parameterization of the module

105739_en_04

PHOENIX CONTACT

5.3

Behavior of the outputs in the event of enabled

switch-off delay for stop category 1

The time until the outputs are actually switched off depends on the parameterization of the

switch-off delay and the event that causes the outputs to be switched off.

For switch-off, please take into consideration the following:

–

Switch-off can be interrupted by switching the output on again.

–

If the parameterization of the module is modified, the modified parameterization

does not take effect until all the outputs have been switched off.

–

If the parameterization is modified before switch-off is complete, a diagnostic

message is generated.

–

If the parameterization is modified, this can result in delayed startup due to the

switch-off delay.

•

Carry out a validation every time the parameterization is modified.

Table 5-2

Switching off the outputs according to the trigger event and the parameterization

Switching off outputs

Influence of set switch-off

delay

Switching off outputs

By the safe controller

Yes

Once the set switch-off delay has elapsed

After a bus error

Yes

Once the set switch-off delay has elapsed

After a short circuit, cross-circuit, failure of

the supply voltage or hardware fault

Immediately (only stop category 0)

WARNING: Delayed switch-off

Stop category 1 results in delayed switch-off.

•

Note the following for stop category 1:

–

The affected outputs are only set to the safe state once the switch-off delay has

elapsed.

–

In the event of an error (excluding bus errors) the affected outputs are switched

off immediately (without delay). In this case, only stop category 0 is supported.

WARNING: Incorrect/insufficient safety distances

Selecting the wrong switch-off delay can result in incorrect safety distances being

designed.

•

When designing the safety distances, take the selected switch-off delay into

consideration.

Содержание Axioline F























































































Результаты поиска

Содержание Axioline F

Отзывы:

Phoenix Contact Axioline F, Руководство пользователя, Страница: 35 / 86

Результаты поиска

Содержание Axioline F

Отзывы: