PCS 103 818
3-3
3-3
a) Remove the Cover DVD Tray (See point 1)
b) Dismantle the Rear Panel Assembly. (See point 6)
c) Loosen 2 screws Q and unhook H2 (see figure 16 & 17)
to remove the Mains Board (pos 1106-A) so that the
Standby Transformer will not obstruct the sliding move-
ment of the DVD / DAC Module assembly.
Note: Due to Standby Transformer size variation, the
removal of Mains Board may not be required in
some version.
d) Loosen 2 screws R (see figure 16), lift the rear portion of
the DVD Module / DAC Module slightly to clear the
stopper and slide it out towards the rear as shown figure
17.
e) Loosen 6 screws T (see figure 16) to separate the DAC
Module.
f)
Release the lug L1 by twisting and bend open the Shield
EMC DAC cover (pos 205) to remove the DAC Board
(pos 1102-C).
Note: Do not bend the Shield EMC DAC cover beyond
45
˚
, otherwise the hindges may be broken.
g) Loosen 5 screws U to separate the DVD module from the
Bracket Mound DVD (pos 197) as shown in figure 18.
7. Dismantling of DVD / DAC Module
Figure 18
7pin Connector for
PC cable for ComPair
U
6. Dismantling the Rear Panel / AV Board / Tuner Module as a complete assembly
a) Loosen 2 screws G on the Rear as shown in figure 14.
b) Release the Bar Tuner (pos 263) from the Plate Front
(pos 254) as shown in figure 10.
c) Release the 2 catches C2 on both sides of the Rear Panel
(see figure 14), pull the complete Rear Panel assembly
backwards slightly and lift it out of the Plate Bottom (pos
236).
d) Remove 1 screw N mounting the ground tag wire, Shield
EMC DAC (pos 205) and Bracket Mound DVD (pos 197)
to Plate Bottom (pos 236) will free the assembly com-
pletely (see figure 16).
Note: During re-assembly of this Rear Panel assembly
it is very important that the Power 5 DVD Module's
bracket be slotted back into the 2 hooks H1 (see
figure 17) on the Bottom Pate and there should be
no gap between the Module's Rucksack (pos
1103-47) and the Plate Rear (pos 234) as shown
in figure 18.
It may be easier to dismantle the Power 5 DVD
Module from the Rear Panel (pos 234) and re-
assemble this Module to the Bottom Plate first
followed by the rest fo the Rear Panel assembly.
Figure 17
H1
H2
Figure 18
There should not be any
gap between the Rucksack
and the Plate Rear
Repair hints on the Left/Right Loudspeaker Box
a) Remove the Cloth Frame assembly.
b) Pull out the 4 Grommet & loosen the 4 screws under the
Grommet mounting location to remove the Woofer Ring.
c) To reach the Tweeter forced open the Front Panel As-
sembly from the wooden LS Box with the help of a minus
screw driver.
Note: This procedure is not recommended because
of high risk that the LS Box will be damaged.
Содержание FW-D5/21
