PFT RITMO XL FU Скачать руководство пользователя страница 37

Страница: 37 / 64

Mixing Pump RITMO XL FU 230V Overview – Operation

Remote control

2019-12-11

34 Remote control

34.1 Working with the remote control

Fig. 62: Remote control

1. Remove dummy connector (1) from control cabinet.

2. Connect remote control.

3. The machine can be switched on or off using the remote

control.

35 Stopping in case of emergency Emergency-stop switch

35.1 Emergency-stop switch

Stopping in case of emergency

In dangerous situation machine movements have to be
stopped as quickly as possible, and the power supply has to
be disconnected.

Fig. 63: Stopping

In case of danger proceed as follows:

1. Turn the main switch to position "0".

2. Secure the main switch against reactivation.

3. Inform responsible person at the operational site.

4. If necessary call for medical assistance and fire brigade.

5. Recover persons from the danger zone, initiate First Aid

measures.

6. Keep access routes free for emergency vehicles.

After the rescue operations

7. If the severity of the emergency permits inform the

competent authorities.

8. Assign specialised personnel with the troubleshooting.

WARNING!
Danger to life from premature reactivation!

On reactivation there is danger to life for all
persons in the danger zone.



Before reactivation ensure that there are no
persons in the danger zone anymore.

9. Check the system before reactivation and ensure that all

safety equipment is installed and functional.

Содержание RITMO XL FU

































































Результаты поиска

Содержание RITMO XL FU

Отзывы:

Бренды по названию

Популярные бренды

PFT RITMO XL FU, Руководство по эксплуатации

Результаты поиска

Содержание RITMO XL FU

Отзывы:

Бренды по названию

Популярные бренды