peplink Pepwave MAX Series Скачать руководство пользователя страница 52

Страница: 52 / 218

https://www.peplink.com

Bandwidth Allowance Monitor

Action

Error! Reference source not found.

is enabled, you will be notified by email

when usage hits 75% and 95% of the monthly allowance.
If

Disconnect when usage hits 100% of monthly allowance

is checked, this WAN

connection will be disconnected automatically when the usage hits the monthly

allowance. It will not resume connection unless this option has been turned off or

the usage has been reset when a new billing cycle starts.

Start Day

This option allows you to define which day of the month each billing cycle begins.

Monthly

Allowance

This field is for defining the maximum bandwidth usage allowed for the WAN

connection each month.

Health Check Settings

Method

This setting specifies the health check method for the WAN connection. This value

can be configured as

Disabled

PING

DNS Lookup

, or

HTTP

. The default method

DNS Lookup

. For mobile Internet connections, the value of

Method

can be

configured as

Disabled

SmartCheck

Health Check Disabled

Содержание Pepwave MAX Series




































































































































































































Результаты поиска

Содержание Pepwave MAX Series

Отзывы:

Похожие инструкции для Pepwave MAX Series

Бренды по названию

Популярные бренды

peplink Pepwave MAX Series, Руководство пользователя

Результаты поиска

Содержание Pepwave MAX Series

Отзывы:

Похожие инструкции для Pepwave MAX Series

Бренды по названию

Популярные бренды