peplink Pepwave MAX Series Скачать руководство пользователя страница 48

Страница: 48 / 218

https://www.peplink.com

To define the threshold manually using specific signal strength values, please click on the

question Mark and the following field will be visible.

General Settings

Independent

from Backup

WANs

If this is checked, the connection will be working independent from other Backup WAN

connections. Those in Backup Priority will ignore the status of this WAN connection, and

will be used when none of the other higher priority connections are available.

Standby State

This option allows you to choose whether to remain connected or disconnected when

this WAN connection is no longer in the highest priority and has entered the standby

state. When

Remain connected

is chosen, bringing up this WAN connection to active

makes it immediately available for use.

Idle Disconnect

When Internet traffic is not detected within the user-specified timeframe, the modem will

automatically disconnect. Once the traffic is resumed by the LAN host, the connection

will be re-activated.

Содержание Pepwave MAX Series




































































































































































































Результаты поиска

Содержание Pepwave MAX Series

Отзывы:

Похожие инструкции для Pepwave MAX Series

Бренды по названию

Популярные бренды

peplink Pepwave MAX Series, Руководство пользователя

Результаты поиска

Содержание Pepwave MAX Series

Отзывы:

Похожие инструкции для Pepwave MAX Series

Бренды по названию

Популярные бренды