peplink Pepwave MAX Series Скачать руководство пользователя страница 38

Страница: 38 / 218

https://www.peplink.com

Allowance

Monitor

connection for each billing cycle. When this option is not enabled, bandwidth usage

of each month is still being tracked but no action will be taken.

Action

If Email Notification is enabled, you will receive an email notification when usage hits

75% and 95% of the monthly allowance.
If the box Disconnect when usage hits 100% of monthly allowance is checked, this

WAN connection will be disconnected automatically when the usage hits the monthly

allowance. It will not resume unless this option has been turned off or the usage has

been reset when a new billing cycle starts.

Start Day

This option allows you to select which day of the month a billing cycle starts.

Monthly

Allowance

This field is to specify the bandwidth allowance for each billing cycle.

Additional Public IP Settings

If you have access to status public IP addresses, you can assign them on this field.

Dynamic DNS Settings

Dynamic DNS

Service Provider

This setting specifies the dynamic DNS service provider to be used for the WAN based

on supported dynamic DNS service providers:

●

changeip.com

●

dyndns.org

●

no-ip.org

●

tzo.com

●

DNS-O-Matic

Select

Disabled

to disable this feature. See

Section 9.5

for configuration details.

Содержание Pepwave MAX Series




































































































































































































Результаты поиска

Содержание Pepwave MAX Series

Отзывы:

Похожие инструкции для Pepwave MAX Series

Бренды по названию

Популярные бренды

peplink Pepwave MAX Series, Руководство пользователя

Результаты поиска

Содержание Pepwave MAX Series

Отзывы:

Похожие инструкции для Pepwave MAX Series

Бренды по названию

Популярные бренды