peplink Pepwave MAX Series Скачать руководство пользователя страница 46

Страница: 46 / 218

https://www.peplink.com

Cellular Settings

SIM Card

Indicate which SIM card this cellular WAN will use. Only applies to cellular WAN with

redundant SIM cards.

Preferred SIM

Card

If both cards were enabled on the above field, then you can designate the priority of

the SIM card slots here.

LTE/3G

This drop-down menu allows restricting cellular to particular band. Click the button

to enable the selection of specific bands.

Optimal

Network

Discovery

Cellular WAsN by default will only handover from 3G to LTE network when there is no active

data traffic, enable this option will make it run the handover procedures after fallback to 3G for

a defined effective period, even this may interrupt the connectivity for a short while.

Band Selection

When set to

Auto,

band selection allows for automatically connecting to available, supported

Содержание Pepwave MAX Series




































































































































































































Результаты поиска

Содержание Pepwave MAX Series

Отзывы:

Похожие инструкции для Pepwave MAX Series

Бренды по названию

Популярные бренды

peplink Pepwave MAX Series, Руководство пользователя

Результаты поиска

Содержание Pepwave MAX Series

Отзывы:

Похожие инструкции для Pepwave MAX Series

Бренды по названию

Популярные бренды