manualshive.com logo in svg

Pentair ULTRATEMP ETi 220, Инструкция по установке и эксплуатации

Поделиться
Скачать
Pentair ULTRATEMP ETi 220 Скачать руководство пользователя страница 29

ULTRATEMP ETI™ Hybrid Heater Installation and User’s Guide

25

 

Operator Menu Tree Guide

(Press Menu Select Button)

Navigating the Operator Menu Screens

Press the MENU SELECT button to view each screen. 
While in the menu screens, if no activity is detected after 
15 seconds, the main screen is displayed.

Pool and Spa Set Point Screens

Displays the pool or spa water temperature set point 
and the actual measured water temperature. This screen 
allows the operator to set the pool or spa set points. 

Efficiency Mode Selection Screen

This screen allows the operator to switch the heater 
between Gas only, Heat Pump only, Hybrid or Dual 
operating modes.

Heater Timer Screen

This feature is an adjustable timer to allow the heater to 
run (green light ON) for a predetermined amount of time 
and then turn OFF (green light OFF).

Remote Mode Screen

Allows the operator to select the Remote mode, Off, 
Relay, RS-485 (serial) or IntelliFlo. In RS-485 Remote 
mode, the heater is controlled by an automation 
controller. In IntelliFlo Remote mode, the heater 
communicates with and activates an RS-485 connected 
IntelliFlo pump when the heater is attempting to heat to 
its set point.

Suction Temperature Screen

Shows the suction line temperature of the refrigerant. 
This screen only appears if the Defrost feature is 
enabled. 

Stack Flue Temperature Screen

Shows the current stack flue temperature.

Alarm Status Screen

Shows if an alarm condition is present. If no alarms are 
present the screen will display ALARM STATUS NONE. 
The control board has the ability to store a 30 Alarm 
history of previous alarms that have occurred. At the 
alarm status screen, press the DOWN arrow. The first 
alarm will be the most recent alarm that has occurred. 
Successive presses (up to 30) of the DOWN arrow will 
display the alarm history in the order of occurrence. The 
operator can scroll back up using the UP button. 

Heat Mode Screen

Displays whether the heater’s pool or spa settings are 
active. The heat mode can be switched between Pool 
and Spa by using the UP and DOWN arrows.  

POOL

GAS/HEATPUMP/HYBRID/DUAL

SET=__     ACT=__

SPA

SET=__     ACT=__

EFFICIENCY MODE

SET - GAS/HEATPUMP/HYBRID/DUAL

HEATER TIMER

REMAINING = NONE

REMOTE MODE

OFF/RELAY/RS-485/INTELLIFLO

ALARM STATUS

SUCTION TEMP

ACTUAL = ___

HEAT MODE

POOL / SPA

GAS/HEATPUMP/HYBRID/DUAL

STACK FLUE TEMP

ACTUAL = ___

ENGLISH

Содержание ULTRATEMP ETi 220





















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды