background image

6

  

FP979   (06-08-20)

INSTALLATION

INSTALLATION (TYPICAL): SEPARATE DISCHARGE

Unplug the primary sump pump before beginning this 
procedure. 

Risk of electrical shock. 

Can shock, 

burn, or kill. 

1.  Allow for overlap when cutting piping and run a trial (dry) 

fitting before you glue.

2.  Use PTFE pipe thread sealant tape on male ends of 

discharge pipe. Thread the 1-1/4” x 1-1/2” elbow (supplied) 
onto the discharge. When tight, the elbow must point up. 

3.  If possible, install the Battery Backup Unit (BBU) on 

the floor of the sump. Be sure that the two pumps do 
not touch each other and do not interfere with switch 
operation. 

NOTE

:

 If debris or gravel is present in the bottom of the 

sump pit that could get sucked up into the pump, set 
both the primary sump pump and the BBU up on bricks or 
cinder blocks to prevent clogging.

4.  If the sump is too small to allow both pumps to sit on 

the bottom of the sump, install an angle bracket on the 
primary sump pump’s discharge pipe with stainless steel 
hose clamps. 

Mount the backup pump on the angle bracket (Figure 2). 

5.  Cut a piece of 1-1/2” PVC pipe to reach from the backup 

pump discharge elbow to about one (1) foot above the 
basement floor. This is the lower discharge pipe. 

6.  To prevent airlocking the pump during operation, drill a 

1/8” hole in the lower discharge pipe about 2” above the 
bottom of the pipe (below floor level). 

7.  Install FP0026-10 check valve (sold separately) on the 

upper end of the pipe. 
Tighten the hose clamps securely. 

BE SURE

 that the flow 

arrows point UP (away from the BBU). If they point down, 
the valve will not pass water and the pump will not work.

8.  Cut a short length of 1-1/2” PVC pipe for a riser pipe and 

clamp it into the top of the check valve.

9.  Install a hose and clamp assembly (sold separately) on the 

top of the riser pipe. For 1-1/2” pipe, remove and discard 
the short piece of 1-1/4” hose in the Hose and Clamp 
Assembly. Leave the hose clamps loose and slide the 
Assembly down below the top of the riser pipe. 

10.  Determine where you want the discharge to exit the 

basement. At that point, drill the necessary holes (large  
enough to have clearance for a 1-1/2” pipe) to allow you 
to run the discharge pipe from above the sump to the 
outdoors.

11.  Install the horizontal discharge pipe. Install a 90° elbow on 

the inside end but do not glue. 

12.  Cut another short piece of 1-1/2” PVC for the Upper 

Discharge Pipe to run from the top of the riser pipe up to 
the 90° elbow. Be sure to allow enough overlap for the glue 
joint in the elbow.

13.  Do a trial fit with NO GLUE, installing the 1-1/2” upper 

discharge pipe in the 90° elbow and the upper discharge 
pipe in the vertical end of the 90° elbow. 

The upper discharge pipe should just fit between the riser 
pipe and the elbow. 

14.  Whenever using PVC primer and PVC cement, follow the 

glue manufacturer’s instructions. 

Risk of 

fire and chemical inhalation.

15.  Make sure that the BBU clears the primary sump pump 

and its switch. If there isn’t room for both pumps to sit 
on the floor of the sump, the BBU will have to be raised 
(depending on your particular situation).

16.  Clean, prime and glue the upper discharge pipe into the 

90º elbow. When the glue has set, slide the Hose and 
Clamp Assembly up to cover the joint and tighten all the 
hose clamps.

17.  Install the Battery Backup Switch as shown, 1” above start 

water level of primary pump. Fasten it to the pipe with 
cable ties. 

18.  Tape the pump cord to the riser pipe so that the plug 

cannot fall into the sump.

19.  Go to BBU WIRING AND SETUP section of this manual for 

wiring instructions. 

20.  Once all wiring is complete, fill your pit with water and 

verify that the primary sump pump removes the water and 
the BBU doesn’t run. 

21.  Then, unplug your primary sump pump and refill your pit 

with water. Verify that the BBU pump removes the water.

22.  Make sure that the power is on to both pumps, and your 

system is ready to use.

Содержание FPDC 30





















































Отзывы: