PENSOTTI PCC 34-H Скачать руководство пользователя | Manualshive

Страница: 69 / 72

background image

INSTALLATION INSTRUCTIONS

66

6.11 Diagnostics

■

Error codes:

E01

Ionization Lock Out / Air Pressure Switch Tripped

E02

Safety Thermostat Tripped

E03

Flue Gas Thermofuse Tripped

H2O Low Water Pressure Alarm
E05

Heating Sensor Malfunction

E12

D.H.W Storage Cylinder Sensor Malfunction

E16

Electric Fan Malfunction

E22

Parameter Programming Request

E35

Flame Detection Malfunction

E42

Fan Speed P.C.B. Malfunction

■

Function codes :

Code

Function

Description

07

Flue test function active

(Chimney-Sweeper)

“High Fire” Test

Pressing the

“service” button for 7 seconds

activates the Flue test function. Pressing the
boiler off button deactivates the function.
The Flue test function operates the boiler at
the maximum heating pressure for
15 minutes without any modulation. The
function is useful for combustion testing.

08

Frost Protection

Central heating circuit

The  function  is  activated  when  the  heating
sensor  senses  a  temperature  of  41  °F.  The
boiler operates at minimum gas pressure with
the 3-way diverter valve in the winter position.
The  function  is  deactivated  when  the
temperature  detected  by  the  sensor  reaches
86°F.

09

Frost Protection

D.H.W. circuit

The function is activated when the sensor
senses a temperature of 40°F. The water
heater operates at minimum gas pressure. The
3-way diverter valve closes in the summer
position and heats the D.H.W. circuit. The
function is deactivated when the D.H.W.
sensor detects a temperature of 46°F.

31

Incompatible Remote Control

Function active when the remote control
connected is not compatible with the printed
circuit board.

110V 60Hz

«
...
67
68
69
70
71
...
»

Содержание PCC 34-H









































































Отзывы:

Нет отзывов

Похожие инструкции для PCC 34-H

Patterson-Kelley MACH Series

Бренд: Harsco Страницы: 51

Бренд: Zip Страницы: 28

Бренд: Beretta Страницы: 80

PELLETHERM SERIES V.2 ?01

Бренд: ZMM Haskovo Страницы: 56

Бренд: R&V Works Страницы: 12

Бренд: eta Страницы: 92

Бренд: Garland Страницы: 40

Бренд: RBI Страницы: 44

Бренд: Bosch Страницы: 68

Бренд: Market Forge Industries Страницы: 16

Бренд: Star Manufacturing Страницы: 6

THERMO-Combi 15

Бренд: Flexiheat Страницы: 22

Dewy Equipe P100 Box

Бренд: Sime Страницы: 80

Бренд: Ferroli Страницы: 196

Бренд: IBC Страницы: 82

Бренд: Nieco Страницы: 36

Inova E20 MC W TOP

Бренд: LAMBORGHINI Страницы: 32

Бренд: Lamborghini Caloreclima Страницы: 121

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды