PENSOTTI PCC 34-H Скачать руководство пользователя | Manualshive

Страница: 29 / 72

background image

INSTALLATION INSTRUCTIONS

26

Always check to make sure that the appliance has an efficient ground system. This requirement is only
satisfied if it has been properly connected to an efficient ground system installed in accordance with the
requirements of current safety standards and carried out by professionally qualified personnel.

This basic safety measure must be checked, verified and carried out by professionally qualified personnel.
Have the electrical system checked by a qualified electrician. The manufacturer will not be held liable for any
damage or injury caused as a result of an inefficient or faulty ground system.

■ Ensure the domestic power supply is checked by a qualified electrician to ensure that it can support the

maximum power absorption of the appliance, as indicated on the rating plate. In particular, make sure that the
cable sizes are adequate for the power absorbed by the appliance;

■ The power supply cable must be replaced by a qualified electrician. If the cable is damaged in any way, switch

off the appliance and have the cable replaced by a suitably qualified electrician;

When using an electrical appliance, a few fundamental rules must be observed:

Do not touch the appliance with damp or wet parts of the body or when barefoot.

Do not pull on the electric wires.

Do not allow the appliance to be used by children or anyone unfamiliar with its operation;

If the unit fails to re-start after any fault, unplug the unit for 30 seconds, then re-plug in the unit

and try to restart with the on/off switch. If the unit fails to restart, call a qualified Technician
for service.

«
...
27
28
29
30
31
...
»

Содержание PCC 34-H









































































Отзывы:

Нет отзывов

Похожие инструкции для PCC 34-H

Бренд: IBC Страницы: 124

Saga Industrial 800 0854

Бренд: OSO HOTWATER Страницы: 112

Calyadra comfort

Бренд: C&M Страницы: 12

Бренд: Ideal Boilers Страницы: 8

Бренд: Glow-worm Страницы: 48

Бренд: Main Страницы: 48

Бренд: Flotec Страницы: 12

Бренд: Biodom Страницы: 61

Бренд: Baxi Страницы: 44

Бренд: Baxi Страницы: 128

Бренд: Climit Страницы: 44

Бренд: TERMOSTROJ Страницы: 16

Бренд: Termomont Страницы: 16

Бренд: Nature's Comfort Страницы: 29

Бренд: TERMOFARC Страницы: 58

Бренд: Viadrus Страницы: 56

Бренд: Anvil Страницы: 2

Бренд: Sime Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды