PENSOTTI PCC 34-H Скачать руководство пользователя страница 68

Страница: 68 / 72

INSTALLATION INSTRUCTIONS

6.10 Troubleshooting

ERROR

CODE

PROBLEM

POSSIBLE CAUSE

REMEDY

E01

NO FLAME / AIR PRESSURE

SWITCH TRIPPED

WITH NO IGNITION

NO GAS.

IGNITION ELECTRODE BROKEN OR GROUNDED.

GAS VALVE MALFUNCTION

MECHANICAL MINIMUM ADJUSTMENT (ON GAS
VALVE) SET TOO LOW OR SLOW IGNITION
ADJUSTMENT SET TOO LOW.

GAS VALVE INLET PRESSURE TOO HIGH (FOR LPG
BOILERS ONLY );

THE CONDENSATE DISPOSAL SYSTEM IS
BLOCKED.

WITH IGNITION

POWER SUPPLY LIVE AND NEUTRAL WIRES
INVERTED

IONIZATION ELECTRODE MALFUNCTION

IONIZATION ELECTRODE CABLE DISCONNECTED

AIR PRESSURE SWITCH

SWITCH OUT OF ORDER

INLET OR OUTLET FLUE GAS DUCTS
OBSTRUCTED

SWITCH CABLE NOT STABLE

WITH NO IGNITION

CHECK MAINS SUPPLY.

REPLACE PART.

REPLACE PART

REGULATE MECHANICAL MINIMUM OR
SLOW IGNITION.

CHECK THE MAXIMUM PRESSURE
SETTING.

CHECK THE CONDENSATE DISPOSAL
SYSTEM AND EMPTY THE
CONDENSATE TRAP.

WITH IGNITION

CONNECT THE POWER SUPPLY WIRES
CORRECTLY

REPLACE PART

CONNECT THE IONIZATION
ELECTRODE WIRE

AIR PRESSURE SWITCH

REPLACE PART

CHECK FLUE GAS DUCTS

CHECK CABLE

E02

SAFETY THERMOSTAT
TRIPPED 203 °F (95 °C)

THERMOSTAT MALFUNCTION OR OUT OF
CALIBRATION

THERMOSTAT CABLE DISCONNECTED

REPLACE PART

CHECK THE WIRING

E03

FLUESAFETY THERMOFUSE

THERMOFUSE BROKEN

THERMOFUSE CABLE DICONNECTED

THERMOFUSE LOCK OUT. (HIGH
FLUETEMPERATURE)

REPLACE PART

CHECK THE ELECTRICAL CONNECTION

RESTART AND CHECK THE
THERMOFUSE

H20

NO WATER IN THE SYSTEM

INSUFFICIENT WATER PRESSURE IN THE SYSTEM
(STOPS AT 0.3 bar)

WATER PRESSURE SWITCH CABLE
DISCONNECTED

WATER PRESSURE SWITCH MALFUNCTION.

FILL THE SYSTEM

CHECK THE WIRING

REPLACE PART

E05

HEATING SENSOR

SENSOR MALFUNCTION OR OUT OF CALIBRATION
(RESISTANCE VALUE 10 kOhms AT 77 °F / 25 °C)

SENSOR CABLE DISCONNECTED OR WET

REPLACE PART

CHECK THE ELECTRICAL CONNECTION

E12

D.H.W STORAGE CYLINDER

SENSOR

SENSOR MALFUNCTION OR INCORRECT
(RESISTANCE VALUE 10 kOhms AT 77 °F / 25 °C)

SENSOR CABLE DISCONNECTED OR WET

REPLACE PART

CHECK THE ELECTRICAL CONNECTION

E16

FAN

BURNT FAN

REPLACE PART

E22

PARAMETER PROGRAMMING

REQUEST

LOSS OF MICROPROCESSOR MEMORY

REPROGRAM PARAMETERS

E35

FLAME DETECTION

MALFUNCTION

aa.

IONIZATION ELECTRODE MALFUNCTION

bb.

IONIZATION ELECTRODE CABLE MALFUNCTION

cc.

PRINTED CIRCUIT BOARD MALFUNCTION

aa.

CLEAN IT OR REPLACE PART

bb.

REPLACE PART

cc.

REPLACE PART

E42

FAN PRINTED CIRCUIT BOARD

dd.

FAN PRINTED CIRCUIT BOARD MALFUNCTION

dd.

REPLACE PART

Содержание PCC 34-H









































































Результаты поиска

Содержание PCC 34-H

Отзывы:

Похожие инструкции для PCC 34-H

Бренды по названию

Популярные бренды

PENSOTTI PCC 34-H, Инструкция по эксплуатации

Результаты поиска

Содержание PCC 34-H

Отзывы:

Похожие инструкции для PCC 34-H

Бренды по названию

Популярные бренды