PENSOTTI PCC 34-H Скачать руководство пользователя страница 66

Страница: 66 / 72

INSTALLATION INSTRUCTIONS

Regulating the water temperature in accordance with the outdoor temperature

The outdoor sensor has to be connected directly to circuit board.

In case of outdoor temperature sensor installation, the climatic compensation curve is set using the
central heating control knob. As the knob (see fig. 2) is rotated, the numbers corresponding to the curve shown
in figure 1 are displayed

The factors governing the correction are reported in figure 1.

The selection of the compensation curve is determined by the maximum delivery temperature Tm and the
minimum outdoor temperature Te.

N.B.

The y-axis values of the delivery temperature Tm refer to standard 185-95 °F appliances or 104-77 °F floor-

mounted appliances. The type of appliance can be programmed using parameter 3 (see 5.1

“Parameter

programming

”).

OUTDOOR SENSOR

DELIVERY TEMPERATURE CORRECTION AS A FUNCTION OF OUTSIDE

TEMPERATURE WITH RESPECT TO THE POSITION OF THE HEATING

TEMPERATURE CONTROL SET BY THE USER

Содержание PCC 34-H









































































Результаты поиска

Содержание PCC 34-H

Отзывы:

Похожие инструкции для PCC 34-H

Бренды по названию

Популярные бренды

PENSOTTI PCC 34-H, Инструкция по эксплуатации

Результаты поиска

Содержание PCC 34-H

Отзывы:

Похожие инструкции для PCC 34-H

Бренды по названию

Популярные бренды