Penrod Warmset Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 32

background image

25

Problem

The

fl

oor

does not

warm when

the system is

turned on

Potential cause

The heating
ribbon has been
damaged

The electrical
connections
were
mismatched

The GFCI has
been tripped

Thick

fl

oor

covering

Solution

Check resistances of the mat in question. Compare
them to the resistances recorded earlier, and with the
resistances stated on the label.

Check all wiring around the parallel connections, breaker,
and any other connections points. Con

fi

rm the correct

voltage is being supplied to the system.

Check for a trip indicator light on the GFCI control. Check
all wiring and for loose connections.

Some  electric  devices  including  electric  motors  can
create  interference  for  GFCIs,  creating  false-trips.  If  the
Warmset  mat  system  shares  a  circuit  breaker  with  any
other devices, move the system to its own breaker.

If the breaker trips again after these steps, replace the
GFCI.

If a thick stone or concrete

fl

oor covering is installed, the

system might take an extended period of time to heat
the surface. Ensure enough time has passed after the
system has been activated.

Note

If you experience any problems with the installation of your
Warmset system, please refer to this section. If the system was not
originally installed by a licensed electrician, consultation with one
is recommended. If problems persist, please contact Warmset Ltd.

All troubleshooting work should be done with the power turned off.

Troubleshooting

«
...
24
25
26
27
28
...
»

Содержание Warmset

































Отзывы:

Нет отзывов

Похожие инструкции для Warmset

Бренд: QUALITY LIFTS Страницы: 13

Бренд: Assa Abloy Страницы: 8

Бренд: CTE Страницы: 130

Бренд: EC POWER Страницы: 62

ATT COMBI LIFT 4.40 S

Бренд: Nussbaum Страницы: 260

Бренд: R. Beck Maschinenbau Страницы: 40

Бренд: ICP DAS USA Страницы: 8

Бренд: Blue Giant Страницы: 24

Бренд: GMI Страницы: 10

Бренд: OSTBERG Страницы: 69

Бренд: Viessmann Страницы: 44

Бренд: Whirlwind Страницы: 2

Бренд: Dormakaba Страницы: 9

Бренд: stertil-KONI Страницы: 102

Бренд: Entrematic Страницы: 124

OUTDOOR HEATING AND COOLING UNIT 379H

Бренд: Bryant Страницы: 6

Бренд: Bryant Страницы: 44

ComfoConnect KNX C

Бренд: Zehnder Rittling Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды