Penrod Warmset Скачать руководство пользователя страница 4

Страница: 4 / 32

Specifications

Warmset Mat

Skill level

requirements

Expected

Performance

The Warmset system is a self-contained heating mat, designed for use em-
bedded in a layer of self-leveling compound and/or thin set. It consists of a
thin heating ribbon

tted onto a mesh.

Although the mesh is designed to be cut in order to facilitate installation
around objects and corners, it is important to note :

The heating ribbon cannot be cut.

This includes shorting the lengths to

t, or splicing two lengths together.

All Warmset products must be installed by knowledgeable and quali

persons. An intermediate skill level in electrical wiring is required. Although
Warmset products may be installed by any quali

ed person (pending local

codes), it is recommended that a certi

ed and licensed electrician roughs in

the power supply wiring.

Please check and adhere to all local codes as they may require all or part of
the installation to be performed by a licensed electrician.

With electric radiant

oor heating, performance is never guaranteed. Warm-

set is designed to deliver the performance listed in the above speci

cations

section. The attainable

ooring temperature is dependent on the type of

oor, and the overall thermal drain of the

oor.

Thorough Insulation is recommended for optimal performance.

Warning

Under no circumstance should the heating ribbon be cut, pierced, or
held in place through the use of staples. Only the mesh can be stapled.

Содержание Warmset

































Результаты поиска

Содержание Warmset

Отзывы:

Похожие инструкции для Warmset

Бренды по названию

Популярные бренды

Penrod Warmset, Руководство по установке

Результаты поиска

Содержание Warmset

Отзывы:

Похожие инструкции для Warmset

Бренды по названию

Популярные бренды