PB Heat Peerless Combi 160 Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 107

background image

20

5.3 - Choosing the
installation location

WARNING!!! Do not store any fl ammable

materials or liquids in the immediate vicinity of the
boiler. A fi re or explosion can result, causing severe
personal injury, death or substantial property damage.

WARNING!!! LIQUEFIED PETROLEUM (L.P.)

PROPANE GAS-FIRED BOILER LOCATION REQUIRES
SPECIAL ATTENTION: 1994 UNIFORM MECHANICAL
CODE section 304.6: “LGP Appliances. Liquefi ed
petroleum gas-burning appliances shall not be
installed in a pit, basement or similar location where
heavier than air gas might collect. Appliances so
fueled shall not be installed in above-grade under-fl oor
space or basement unless such location is provided
with an approved means for removal of unburned
gas.” Failure to comply with this provision could
result in severe personal injury or substantial property
damage.

CAUTION!!! The boiler must be installed on a

vertical wall constructed to bear its weight or the boiler
and building may be damaged.
NOTE: The boiler must never be installed on carpeting.

CAUTION!!!

This boiler is not designed for direct

outdoor installation. If installed outside of the structure
that it supplies hot water too, it must be sheltered so it is
protected from rain, wind, sun and frost. NEVER place this
boiler in a location that would subject it to temperatures at
or near freezing. Failure to properly locate this boiler can
result in premature failure voiding the warranty.

When locating the boiler the following factors must be
considered:
• the location of vent/air intake terminals;
• connection to the gas supply;
• connection to the water supply;
• connection to the heating system;
• connection to the domestic hot water system;
• connection to the electrical supply;
• disposal of the condensation produced by the boiler;
• connection to the room thermostat;
• piping of the safety relief valve discharge;
• possible connection of the outdoor temperature sensor;
• possible connection of an indirect storage tank, see

section 7.1.

5 - INSTALLATION - Mounting & gas and water connections

«
...
18
19
20
21
22
...
»

Содержание Peerless Combi 160












































































































Отзывы:

Нет отзывов

Похожие инструкции для Peerless Combi 160

Бренд: Water Heater Innovations Страницы: 24

Бренд: Vaillant Страницы: 76

Бренд: Riello Страницы: 196

KSM-Multistoker 575-50

Бренд: KSM-Stoker Страницы: 68

Бренд: Wells Страницы: 30

Бренд: VOKERA Страницы: 12

Бренд: Biasi Страницы: 48

Бренд: Flotec Страницы: 12

Бренд: Rinnai Страницы: 2

Бренд: Riello Страницы: 56

Бренд: U.S. Boiler Company Страницы: 7

Бренд: TriangleTube Страницы: 24

Бренд: Wolf Страницы: 12

Бренд: Wolf Страницы: 28

Бренд: Wolf Страницы: 48

Бренд: Wolf Страницы: 2

Бренд: Potterton Страницы: 64

Бренд: Worcester Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды