PB Heat Peerless Combi 160 Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 107

background image

104

can assume the follow values:

61 - for boiler at NATURAL gas;
62 - for boiler at LP gas;

can assume the follow values:

00 - 230Vac, 50Hz, °C;
01 - 230Vac, 50Hz, °F;
02 - 120Vac, 60Hz, °C;
03 - 120Vac, 60Hz, °F

16 - READ OUT FLOW CHART

CAUTION!!! Changing

these parameters could cause the
boiler and therefore the system to
malfunction. For this reason, only
a qualifi ed technician who has
in-depth knowledge of the boiler
should change them.

The boiler’s micro-processor makes
this menu of parameters available to
the

qualifi ed technician for the setting

of the appliance .

Basic functionalities selection and Speed blower
selection (see below for more explications)

Main electrical supply and temperature unit
selection (see below for more explication)

Domestic functionalities selection. Must be
always at 00

Master or slave selection in a batterie
confi guration. Must be always at 00.

Rotating selection in a batterie confi guration.
Must be always at 00.

To enter this menu you must:
1. turn the main electrical supply Off;
2. move the switch n° 7 (see fi gure

21, item “D”) to the ON position;

3. turn the main electrical supply On.
Now “ty” is displayed. Use plus and
minus keys to change the value; use
RESET key to save the value and
swap to the next parameter.

To exit this menu you must:
1. turn the main electrical supply Off;
2. move the switch n° 7 (see fi gure

21, item “D”) to the Off position;

can assume the follow values:

00, 01 and 02. Must be always at 00.

If readable, can assume the follow values:

00, 01, 02, 03, 04, 05, 06, 07 and 08. Must be always
at 00.

If readable, can assume the follow values:

00, 01, 02, 03, 04, 05, 06, 07 and 08. Must be always
at 00.

«
...
102
103
104
105
106
...
»

Содержание Peerless Combi 160












































































































Отзывы:

Нет отзывов

Похожие инструкции для Peerless Combi 160

Бренд: Water Heater Innovations Страницы: 24

Бренд: A.O. Smith Страницы: 56

Бренд: IBC Страницы: 7

Бренд: Zip Страницы: 28

EGIS PLUS 24 CF

Бренд: Ariston Страницы: 12

Бренд: Kalvis Страницы: 12

GREENSTAR UTILITY

Бренд: Worcester Страницы: 64

Бренд: Warmhaus Страницы: 48

Бренд: U.S. Boiler Company Страницы: 9

Combi Compact ECO RF 24

Бренд: Intergas Страницы: 4

Бренд: Radijator Страницы: 58

Бренд: Radijator Страницы: 75

Ekoflux RK 34/B

Бренд: Radiant Страницы: 60

Бренд: STIEBEL ELTRON Страницы: 16

Бренд: Aerco Страницы: 108

Бренд: Nature's Comfort Страницы: 34

Бренд: Sigma Страницы: 32

Бренд: Bryan Boilers Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды