PB Heat Peerless Combi 160 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 107

background image

11

(b) Exemptions
The following equipment is exempt
from 248 CMR 5.08(2)(a) 1 through
4:

1. The equipment listed in Chapter

10 entitled “Equipment Not
Required To Be Vented” in the
most current edition of NFPA 54
as adopted by the Board; and

2. Product Approved side wall

horizontally vented gas fueled
equipment installed in a room
or structure separate from the
dwelling, building or structure used
in whole or in part for residential
purposes.

(c) MANUFACTURER
REQUIREMENTS - GAS
EQUIPMENT - VENTING SYSTEM
PROVIDED.

When the manufacturer of Product
Approved side wall horizontally vented
gas equipment provides a venting
system design or venting system
components with the equipment,
the instructions provided by the
manufacturer for installation of the
equipment and the venting system
shall include:
1. Detailed instructions for the

installation of the venting system
design or the venting system
components; and

2. A complete parts list for the

venting system design or venting
system.

(d) MANUFACTURER
REQUIREMENTS – GAS
EQUIPMENT - VENTING SYSTEM
NOT PROVIDED.

When the manufacturer of a Product
Approved side wall horizontally
vented gas fueled equipment does not
provide the parts for venting the fl ue
gases, but identifi es “special venting
systems”, the following requirements
shall be satisfi ed by the manufacturer:
1. The referenced “special venting

system” instructions shall be
included with the appliance or
equipment installation instructions;
and

2. The “special venting systems”

shall be Product Approved by
the Board, and the instructions
for that system shall include a
parts list and detailed installation
instructions.

1 - INSTALLATION - CODE REQUIREMENTS

(e) A copy of all installation
instructions for all Product
Approved side wall horizontally
vented gas fueled equipment, all
venting instructions, all parts lists
for venting instructions, and/ or
all venting design instructions
shall remain with the appliance or
equipment at the completion of the
installation.

«
...
9
10
11
12
13
...
»

Содержание Peerless Combi 160












































































































Отзывы:

Нет отзывов

Похожие инструкции для Peerless Combi 160

Бренд: IDEAL Страницы: 8

Aerco Modulex EXT Series

Бренд: Watts Страницы: 144

Бренд: Excel Страницы: 65

Бренд: Easylife Страницы: 4

UTICA BOILERS MAC-150

Бренд: ECR International Страницы: 92

Logano plus GB102

Бренд: Buderus Страницы: 12

Бренд: Protherm Страницы: 19

Бренд: OSO HOTWATER Страницы: 48

Бренд: Chaffoteaux & Maury Страницы: 44

Бренд: Immergas Страницы: 27

Бренд: Immergas Страницы: 30

Бренд: STYLEBOILER Страницы: 24

Бренд: Viessmann Страницы: 136

Бренд: Ideal Boilers Страницы: 48

Бренд: Danfoss Страницы: 8

evolution EV HFDX

Бренд: DOMUSA Страницы: 48

Бренд: Unical Страницы: 44

INDEPENDENCE IN10 CANADA

Бренд: Burnham Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды