background image

7200 Monitor Instruction Manual

26  Technical Specification

26.1  General

Supply Voltage ............................... 85-264VAC, 50/60 Hz, 
Power Consumption........................15 VA
Supply Fuse....................................1.6A Anti surge 20 x 5mm (Fitted Internally)
Operating Temperature...................0 to 50°C
Storage Temperature......................-20 to 70°C
Display Resolution..........................0.1%
Response Time...............................0.2 to 120 Seconds (User selectable)
Linearity...........................................(Refer to sensor specification)
Accuracy.........................................(Refer to sensor specification)
Repeatability...................................(Refer to sensor specification)

26.2  Alarm Outputs

Number of Outputs..........................2 SPCO
Alarm Types....................................Low, High, Fault (User configurable)
Operation........................................Fail Safe (De-energised in alarm condition)
Relay Rating....................................5 A @ 230 VAC, 5 A @ 30 VDC

26.3  Analogue Output

Type:...............................................4-20 mA/0-20 mA/0-5 V (User configurable)
Resolution:......................................Better than 0.5%
4-20mA Maximum Output Load:.....1000 Ohms
0-20mA Maximum Output Load:.....1000 Ohms
0-5V Minimum Output Load:...........1000 Ohms

26.4  EMC

EMC:...............................................EN 61000-6-1(2001)  EN 61000-6-3(2001)

26.5  Field Mount

Dimensions:....................................160 

×

 166 

×

 73 mm (h 

×

 w 

×

 d)

Weight:............................................1 Kg
Environmental Rating:.....................IP65
Material:..........................................ABS
Cable Entry:....................................4 

×

 PG11 (2 factory fitted, 2 supplied separately)

Terminals:.......................................Max conductor cross section 2.5 mm

2

 

Page 46 of 50

167300IM-Issue 12 Issue Date 14/10/2014

Содержание 7200



















































Отзывы: