ParTech 7200 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 50

ParTech 7200 Скачать руководство пользователя страница 36

7200 Monitor Instruction Manual

17 Diagnostics

The diagnostics menu provides information regarding the internal setup and operation of the instruments and is a very
useful facility in assisting problem diagnosis. If a problem has occurred, contact Partech technical support for
assistance.

17.1 Sensor Input

This display indicates the input signals from the sensor, U: is the raw signal from the sensor D: is the raw sensor
signal with damping applied, S: is the approximate supply current to the sensor, L: is an internally used version of the
damped sensor signal and M: is the display value.

17.2 Sensor %

This is a bar graph display of the undamped and damped sensor signals on a 0 to 100% scale, where 100% equates
to the sensors upper range value.

17.3 Calibration Values

This indicates the internal values used to store the calibration and sensor setup data.

17.4 Factory Values

These values are set during factory calibration of the unit.

17.5 Diagnostic Values

These are additional values that are helpful when diagnosing instrument problems.

17.6 Diagnostic Download

This facility allows the downloading of the calibration, factory and internal values using the RS232 serial interface.

17.7 Opto Inputs

This display indicates the status of the opto-input signals from self-cleaning sensors.

17.8 ADC Inputs

The analogue to digital converter input values can be viewed using this menu.

Page 36 of 50

167300IM-Issue 12 Issue Date 14/10/2014

«
...
34
35
36
37
38
...
»

Содержание 7200



















































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды