Panduit Atlona OmniStream AT-OMNI-121 Скачать руководство пользователя страница 121

Страница: 121 / 129

AT-OMNI-121 / AT-OMNI-122

121

Appendix

Go to the

Notifications

menu on the decoder.

If the test fails, it could be that less than 100% of packets are received, indicating connectivity, but with some

amount of packet loss. If it shows “No one replied!” or if the target decoder is not shown in results, it could

indicate that there is a connectivity issue or that the decoder is not subscribed to the correct video multicast

address.

Hovering the mouse over the

Description

field will provide the full IP address of each decoder which received

the test, as shown below. If multiple decoders were tested, additional IP addresses will be displayed.

If the test passed, information similar to the following will be displayed. Note the information in the

Description

field: “100% of packets received ...” indicates no packets were dropped / zero loss.

Hovering the mouse over the

Description

field will display the full IP address of the encoder from where the

packets originated.

Click the

CLEAR

button to remove the test results from the

Notification

page.

Содержание Atlona OmniStream AT-OMNI-121


































































































































Результаты поиска

Содержание Atlona OmniStream AT-OMNI-121

Отзывы:

Похожие инструкции для Atlona OmniStream AT-OMNI-121

Бренды по названию

Популярные бренды

Panduit Atlona OmniStream AT-OMNI-121, Руководство пользователя

Результаты поиска

Содержание Atlona OmniStream AT-OMNI-121

Отзывы:

Похожие инструкции для Atlona OmniStream AT-OMNI-121

Бренды по названию

Популярные бренды