Panasonic WH-MHF09G3E5 Скачать руководство пользователя страница 92

Страница: 92 / 138

16.5.8 Outdoor Low Pressure Abnormality (H63)

Malfunction Decision Conditions:

During operation of heating, when the outdoor low pressure sensor output signal is 0Vdc or 5Vdc.

Malfunction Caused:

1 Faulty

connector

connection.

2 Faulty

sensor.

3 Faulty outdoor unit PCB (main).

Abnormality Judgment:

Continue 4 times in 20 minutes.

Troubleshooting:

For safety reason and to prevent component breakdown,
always switch off the power before remove and connect the component.

Check the CN-LPS connector connection:
- Turn OFF the power.
- Check the connector connection.

Check the continuity of the outdoor unit PCB (main)
high pressure sensor connector CN-LPS:
- Plug out connector from the outdoor unit PCB (main).
- Measure the continuity pin 2 & 3 (GND) and pin 2 &

4 (5 V) of CN-LPS.

Is the CN-LPS connector

connection normal?

Is the measured voltage

0Vdc or 5Vdc?

Reconnect the low pressure sensor

connector to the outdoor unit PCB

(main). Turn ON the power and run

the system. Measure the DC voltage

pin 2 & 3 (GND) of CN-LPS.

Is there any continuity?

Yes

- Connector poor contact.
- Correct the connection.

- Defect in outdoor unit

PCB (main).

- Replace the outdoor

unit PCB (main).

- Defect in outdoor low

pressure sensor.

- Replace the outdoor

low pressure sensor.

- Defect in outdoor unit

PCB (main).

- Replace the outdoor

unit PCB (main).

Содержание WH-MHF09G3E5











































































































































Результаты поиска

Содержание WH-MHF09G3E5

Отзывы:

Похожие инструкции для WH-MHF09G3E5

Бренды по названию

Популярные бренды

Panasonic WH-MHF09G3E5, Руководство по обслуживанию

Результаты поиска

Содержание WH-MHF09G3E5

Отзывы:

Похожие инструкции для WH-MHF09G3E5

Бренды по названию

Популярные бренды