Panasonic WH-MHF09G3E5 Скачать руководство пользователя страница 91

Страница: 91 / 138

16.5.7 Water Flow Switch Abnormality (H62)

Malfunction Decision Conditions:

During operation of heating, the water flow detected by the indoor water flow switch is used to determine water
flow error.

Malfunction Caused:

1 Faulty

water

pump.

2 Water leak in system.
3 Faulty

connector

connection.

4 Faulty water flow switch.
5 Faulty indoor unit PCB (main).

Abnormality Judgment:

Continue for 10 seconds (but no judgment for 9 minutes after compressor startup/restart).

Troubleshooting:

For safety reason and to prevent component breakdown,
always switch off the power before remove and connect the component.

Check the system water pump.

Is the CN-FLOW connector

connection normal?

Is there any continuity?

Check the system water passage.

Is the water pump working?

Is there any water leakage?

Yes

Replace the faulty water

pump.

- Connector poor contact.
- Correct the connection.

- Defect in indoor water flow

switch.

- Replace the indoor water

flow switch.

- Defect in indoor unit PCB

(main).

- Replace the indoor unit PCB

(main).

Fix the system water

leakage.

Check the CN-FLOW connector connection:
- Turn OFF the power
- Check the connector connection

Check the indoor water flow switch:
- Plug out connector from the indoor

unit PCB (main).

- Dismantle the water flow switch.
- Position the water flow switch in

reverse direction (downward).

- Measure the continuity of the

water flow switch.

Содержание WH-MHF09G3E5











































































































































Результаты поиска

Содержание WH-MHF09G3E5

Отзывы:

Похожие инструкции для WH-MHF09G3E5

Бренды по названию

Популярные бренды

Panasonic WH-MHF09G3E5, Руководство по обслуживанию

Результаты поиска

Содержание WH-MHF09G3E5

Отзывы:

Похожие инструкции для WH-MHF09G3E5

Бренды по названию

Популярные бренды