Panasonic WH-MHF09G3E5 Скачать руководство пользователя страница 100

Страница: 100 / 138

100

16.5.16 Unspecified Voltage between Indoor and Outdoor (H95)

Malfunction Decision Conditions:

The supply power is detected for its requirement by the indoor/outdoor transmission.

Malfunction Caused:

1 Insufficient power supply.
2 Faulty outdoor unit PCB (noise filter/main).

Troubleshooting:

For safety reason and to prevent component breakdown,
always switch off the power before remove and connect the component.

Is the measured AC voltage

230V?

Correct the power

supply.

- Defect in outdoor

unit PCB (noise filter).

- Replace the outdoor

unit PCB (noise filter).

- Defect in outdoor unit

PCB (main).

- Replace the outdoor unit

PCB (main).

- Defect in outdoor unit

PCB (main).

- Replace the outdoor unit

PCB (main).

- Defect in outdoor unit

PCB (main).

- Replace the outdoor unit

PCB (main).

- Connector poor contact.
- Correct the connection.

Check the AC voltage from outdoor unit PCB (noise filter):
- Turn OFF the power.
- Plug out connector AC-BLK, CN-BLK & CN-WHT from

the outdoor unit PCB (noise filter).

- Turn ON the power.
- Measure the AC voltage between AC-BLK & CN-WHT.

Check the AC voltage supply to outdoor unit PCB (main):
- Turn OFF the power.
- Reconnect connector AC-BLK, CN-BLK & CN-WHT to

the outdoor unit PCB (noise filter).

- Turn ON the power.
- Measure the AC voltage between AC-BLK & CN-WHT.

Is the measured AC voltage

230V?

Check the rectification voltage

between DCP & DCN.

Is the measured voltage

between DCP & DCN~325 Vdc?

Check the DC filter (capacitor)

PCB connector connection.

Is the DC filter (capacitor) PCB

connector connection normal?

Yes

Check the supply voltage.

Supply voltage as specified?

Содержание WH-MHF09G3E5











































































































































Результаты поиска

Содержание WH-MHF09G3E5

Отзывы:

Похожие инструкции для WH-MHF09G3E5

Бренды по названию

Популярные бренды

Panasonic WH-MHF09G3E5, Руководство по обслуживанию

Результаты поиска

Содержание WH-MHF09G3E5

Отзывы:

Похожие инструкции для WH-MHF09G3E5

Бренды по названию

Популярные бренды