Panasonic WH-MHF09G3E5 Скачать руководство пользователя страница 44

Страница: 44 / 138

B. If Remote Control Cable Is Exposed

1 Install the remote control lower case to the

wall with the two accessory screws (4).

2 Fasten the screws properly until screw head is

lower than the rib and reach the base of
remote control lower case to ensure they do
not damage the PCB inside the remote control
(1).

3 The feeding-out direction for the remote

control cable can be either via top, left or right
side.

4 Use nipper to cut a notch at the upper case.

(Select the intended feeding-out position)

5 Route the remote control cable (2) inside the

lower case in accordance with the intended
feeding-out direction. (Refer to the illustration
at below)

6 Insert firmly the connector of remote control

cable (2) to connector (CON1) in the upper
case circuit board. (Refer to the illustration at
below)

7 Secure the remote control upper case to the

lower case with the tabs provided.

11.4.6 Connecting The Remote Control Cable To Mono Bloc Unit

WARNING

Be sure to turn off the main power before installing and
connecting the remote control. Otherwise, it will cause the
electrical shock.

1 Remove the cabinet front plate.
2 Connect the remote control cable with the

provided connector as shown in below
illustration. (Refer wiring diagram for detail.)

3 Guide the remote control cable through the

clamper and Bushing

(Refer illustration “How to connect Remote
Control to Provided Connector” for detail.)

4 Reinstall the cabinet front plate after

connection complete.

How to connect Remote Control to Provided

Connector

Wall

Rib

Screw (4)

Remote
control lower
case

Remote control cable (2)

Wall

Upper case

Upper tab

Connector (CON1)

Lower case

Screw (4)

Lower tab

Left

feeding-

out

position

Lower

case

Top feeding-out

position

Remote

control

cable (2)

Notches

Connector

(CON1)

Upper case

Lower case

Tabs

Right

feeding-

out

Bind the wired
remote control
cable and all
power supply

with band strap

cords to the tube

Bushing

(field supply)

Clamp the wired
remote control cable
with clamper.

Wired remote
control cable

Apply cut

Connect the wired remote
control cable with the connector
provided here

Remote
control

PCB

Plug in firmly

Provided
Connector

Remote
Control
Connector

Remove this dummy connector
cap first, before plug in

Содержание WH-MHF09G3E5











































































































































Результаты поиска

Содержание WH-MHF09G3E5

Отзывы:

Похожие инструкции для WH-MHF09G3E5

Бренды по названию

Популярные бренды

Panasonic WH-MHF09G3E5, Руководство по обслуживанию

Результаты поиска

Содержание WH-MHF09G3E5

Отзывы:

Похожие инструкции для WH-MHF09G3E5

Бренды по названию

Популярные бренды