manualshive.com logo in svg

Panasonic U-26PE1U6, Технические данные и руководство по обслуживанию

Поделиться
Скачать
Panasonic U-26PE1U6 Скачать руководство пользователя страница 91

1-83

1-82

1. Specifications

1-10. External Static Pressure Setting

Concealed Duct (Type F2)

For concealed duct type indoor units, the ventilating resistance so-called “external static pressure” becomes greatly

different depending on the connected duct length, shape, number of air outlet ports and types of filters.

When installing this unit, be sure to carry out the external static pressure setting in order to operate in the rated airflow 

volume. Choose one of the following methods from “a”, “b”, “c” or “d” as shown in the flow chart (within the dotted lines) 

and then make the setting accordingly.

a. No setting modification .............................................................................:  Use-as-is at shipment (there are cases in which the 

setting may differ from the shipment setting when 
reset after once setting the external static pressure.)

b. Manual setting (set with the PC board) ....................................................:  For high static pressure. Switching method with the 

short-circuit connector.

c. Manual setting (set with the wired remote controller) ...............................:  Low static pressure ~ high static pressure
d. Auto airflow volume setting (set on the wired remote controller)  .............:  Air outlet volume is automatically adjusted to the rated 

airflow volume with the auto airflow control drive.

Flow of External Static Pressure

Finish the ducting and electrical wiring and prepare it for use. (Note (1))

External static pressure should be set during initial operations after installation (before 

the cooling and heating test run).

When operating with group control (connecting multiple indoor units with one wired 

remote controller), make the concealed duct type to the main unit.

Start external static pressure setting

a. No setting modification

b. Manual setting

(set with the PC board)

TP3 or TP1 short-circuit 

Refer to section “1-10-1. 

How to Set on PC Board”.

c. Manual setting

Item code “b0” : 0~15 setting 

(*Note (3)) (* Note (4))

Refer to section 1-10-2 or 1-10-3.

d. Auto airflow volume setting 

(* Note (4)) Item code “b0” : 

-2 setting 

Refer to section 1-10-2 or 1-10-3.

Operation checks for external static pressure settings (*Note (2))

Refer to section 1-10-2 or 1-10-3.

Check if the setting is within the range of use on the PQ diagram.

If out of range, adjust until it becomes within the range of use.

This can be omitted if deemed unnecessary in the event of the same installation/set-up being available.

Auto airflow volume control 

operations 

(*Note (5))

Refer to section 1-10-2 or 1-10-3.

Test operation display will disappear. (*Note (6))

External static pressure setting completed

Timer remote controller available

Lines 

15

 and 

14

 

settings (high static pressure) on 

the PQ diagram required

Set the rated airflow 

volume with the exception of lines 

15

, 

14

 and, 

8

Line 

8

 (set at 

shipment) on the PQ diagram 

designed and installed

No

No

No

No

Yes

Yes

Yes

Yes

1

SM830203-04.indb   83

15/10/16   10:44:45

Содержание U-26PE1U6










































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды