manualshive.com logo in svg

Panasonic U-26PE1U6, Технические данные и руководство по обслуживанию

Поделиться
Скачать
Panasonic U-26PE1U6 Скачать руководство пользователя страница 259

4-15

4-14

4. Service procedures

NOTE

The temperature display appears as “- - - -” for units that are not connected.

* If monitor mode is engaged while normal operation is in progress, only the parts of the LCD display shown in the  
  figure will change. Other parts continue to display the same information as during normal operation.

 <Procedure of CZ-RTC4> 

Sensor installation

Sensor 

Sensor type

Sensor

Sensor type

s

s

e

r

d

d

a

s

s

e

r

d

d

a

n

o

i

t

a

c

o

l

00

Room temp. 

05

–

(temp. used for control)*

01

Remote controller temp.

06

Discharge temp.

Indoor unit

02

Indoor intake temp.

07

–

03

Indoor heat exchanger temp. (E1 )

08

–

04

Indoor heat exchanger temp. (E2 )

09

–

0A

Discharge temp. (TD)

12

–
–

3

1

–

b

0

 t

n

e

r

r

u

C

4

1

–

C

0

(AC current)

Outdoor unit

0d

Intake temp. (TS)

15

Outdoor electronic control

valve position

0E

Outdoor heat exchanger temp. (C1 )

16

–

0F

Outdoor heat exchanger temp. (C2 )

17

–
–

8

1

–

0

1

11

Outdoor air temp.

19

–

Sensor Temperature Correlation Table

* Main unit only when group control is enabled

Figure: Sample display when discharge 
 

temperature at unit No. 1-1 is 185˚F

Sensor Temperature Display Function (Displayed both when operating and stopped)

The below check procedure can be used to display
all remote controller, indoor unit, and outdoor unit
sensor temperatures.

 <Check procedure>

(1) Press and hold the button and button simultaneously

for 4 seconds or longer.

(2) Unit No. X-X (main unit No.), item code XX (sensor

address), and service monitor 00XX (sensor tem-
perature) appear on the remote controller LCD. (See
figure.)

(3) Press the temperature setting and buttons and

change the item code to the sensor address of the
sensor that you want to monitor.
(For the relationship between the sensor address and
the sensor type, refer to the below Sensor Tempera-
ture Correlation Table.)

(4) During group control and simultaneous operation

multi control, press the button and change to the unit
that you want to monitor.

(5) Press the button to return to normal remote controller

operation.

NOTE

The temperature display reads “- - - - ” for units that are
not connected.

If monitor mode is selected during normal operation,
the only parts of the LCD that change are those
shown in the figure.
All other displays do not change, and remain as they
were during normal operation.

 Press and hold the 

 and 

 buttons 

simultaneously for 4 seconds or longer.

 The unit No. “X-X” (main unit No.), item code “

” 

(sensor address), and servicing monitor “

” 

(sensor temperature) are displayed on the remote 
controller LCD display. (See Fig. 3 at right.)

 Press the temperature setting 

/

and select the item code to the address of the 

buttons 

sensor to monitor.

 If group control is in effect, press the 

to select the unit to monitor.

button 

Press the temperature setting buttons to select the 
item code to change.

 Press the 

 button to return to normal remote 

*  Display shows a discharge temperature of 
   00XX at unit No. 1-1.

controller display.

Fig. 3

A

°

°

CZ-RTC4

1

2

3

4

5

3

3

4

1

2

4

5

4

4

SM830203-04.indb   15

15/10/15   11:04:53

Содержание U-26PE1U6










































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды