Panasonic U-26PE1U6 Скачать руководство пользователя

Страница: 213 / 297

2-7

2-6

2. Processes and functions

Overcurrent protection control

(1) If the overcurrent protection circuit detects

abnormal current, the compressor is stopped. (Error

count = 1.) The compressor then restarts after 3

minutes.

(2) If compressor start/stop is repeated 4 times (error

count = 4), alarm "P26", "P29" or "H01" (count = 2

in this case only) occurs. Operation stops and does

not restart.

Current release value shift control

(1) This control is intended to improve compressor

reliability by preventing continuous high-frequency

operation under overload conditions when the

outdoor air temperature is high, and by preventing

intermittent operation through "control for

prevention of high cooling loads".

(2) The control value for "current release control" is

corrected according to the outdoor air temperature

(TO).

Depending on the temperature, the control value is

lowered to 50 – 90% for cooling operation, and to

60 – 98% for heating operation.

Freeze prevention (low-temperature release) control

The below control is performed during cooling operation

(including dehumidifying operation), using whichever of

the indoor heat exchanger temperatures (E1 or E2) is

lower. (See the figure below.)

(1) If a temperature in the "J" area (operating

frequency reduction and thermostat OFF area) is

detected for 6 minutes, the compressor operating

frequency is reduced. The compressor operating

frequency is reduced every 30 seconds as long as

the temperature remains within this area.

(2) If the temperature is in the "K" area (operating

frequency increase-prohibit area), the compressor

operating frequency is maintained.

(3) If the temperature is in the "H" area (operating

frequency control area), and the outdoor air

temperature is less than 90°F, the compressor

maximum operating frequency is limited according

to the indoor unit fan speed.

(4) If the temperature is in the "I" area (normal

operating area), the compressors operate normally.

(5) If the temperature is continuously in the "J" area

and the compressor operating frequency reaches 0,

then temperature A (temperature for changing from

"J" area to "H" area) is raised from 41°F to 46°F,

and operation continues with the thermostat OFF

until the temperature reaches the "H" area.

Heating high-load control

The below control is performed during heating operation,

based on the indoor heat exchanger temperature MAX

(E1,E2).
(1) If the temperature is in the "M" area (operating

frequency reduction and thermostat OFF area), the

compressor operating frequency is reduced.

The compressor operating frequency is reduced

every 30 seconds as long as the temperature

remains within this area.

(2) If the temperature is continuously in the "M" area,

the thermostat turns OFF.

(3) If the temperature is in the "N" area, operating

frequency increases are prohibited.

(4) If the temperature is in the "L" area, the operating

frequency is raised to the original frequency (the

frequency prior to frequency reduction) by 6 Hz

every 60 seconds.

* When the compressor turns ON and the E2

temperature rises, the temperature at which the

"M" area is first entered is 124°F (Type 36, 42)

or higher than 129°F (Type 26).

If the E1, E2 temperature subsequently falls to

the "L" area, the temperature for entering the "M"

area is raised to 126°F (Type 36, 42) or 133°F

(Type 26).

However if the E1, E2 temperature falls to the "L"

area and falls below 86°F, then the temperature for

entering the "M" area is changed back to 124°F

(Type 36, 42) or 129°F (Type 26).

(36, 48 types)

(Type 26) (Type 36, 48)

SM830203-04.indb 7

15/10/15 11:03:37

Содержание U-26PE1U6










































































































































































































































































































Результаты поиска

Содержание U-26PE1U6

Отзывы:

Похожие инструкции для U-26PE1U6

Бренды по названию

Популярные бренды

Panasonic U-26PE1U6, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание U-26PE1U6

Отзывы:

Похожие инструкции для U-26PE1U6

Бренды по названию

Популярные бренды