Panasonic U-26PE1U6 страница 105 Скачать руководство пользователя

Страница: 105 / 297

1-97

1-96

1. Specifications

1-12. ELECTRICAL WIRING

General Precautions on Wiring

Recommended Wire Length and Wire Diameter for Power Supply System

You must follow LOCAL ELECTRICAL CODES for wiring.

Outdoor Unit

Type

Time delay fuse or

circuit capacity

U-26PE1U6
U-36PE1U6
U-42PE1U6

30 A
35 A
40 A

Type

Time delay fuse or

circuit capacity

U-26PS1U6
U-36PS1U6
U-42PS1U6

25 A
30 A
35 A

Indoor Unit

Type

Time delay fuse or

circuit capacity

U1, K1, T1, F1,

F2, U2, K2, T2

15 A

Control Wiring

(A) Inter-Unit Control Wiring

(B) Remote Control Wiring

(C) Control Wiring For Group Control

AWG #18

Use high voltage wire (300 V)

AWG #18

(0.75 mm

)

AWG #18

*1 -

(0.75 mm

)

Max. 650 - ft. (Total)

Max. 1,650 ft.

Max. 3,300 ft.

AWG=American Wire Gauge

With ring-type wire terminal

(1)

Before wiring, confirm the rated voltage of the unit as shown on its nameplate, then carry out the wiring closely

following the wiring diagram.

WARNING

(2) This equipment is strongly recommended to be installed with Earth Leakage Circuit Breaker (ELCB) or

Residual Current Device (RCD). Otherwise, it may cause electrical shock and fire in case of equipment

breakdown or insulation breakdown.

Earth Leakage Circuit Breaker (ELCB) must be incorporated in the fixed wiring in accordance with the

wiring regulations. The Earth Leakage Circuit Breaker (ELCB) must be an approved 15 A, having a

contact separation in all poles.

(3) To prevent possible hazards from insulation failure, the unit must be grounded.

(4) Each wiring connection must be done in accordance with the wiring system diagram. Wrong wiring may cause the

unit to misoperate or become damaged.

(5) Do not allow wiring to touch the refrigerant tubing, compressor, or any moving parts of the fan.

(6) Unauthorized changes in the internal wiring can be very dangerous. The manufacturer will accept no responsibility

for any damage or misoperation that occurs as a result of such unauthorized changes.

(7) Regulations on wire diameters differ from locality to locality. For field wiring rules, please refer to your LOCAL

ELECTRICAL CODES before beginning.

You must ensure that installation complies with all relevant rules and regulations.

(8) To prevent malfunction of the air conditioner caused by electrical noise, care must be taken when wiring as follows:

The remote control wiring and the inter-unit control wiring should be wired apart from the inter-unit power wiring.

Use shielded wires for inter-unit control wiring between units and ground the shield on single side.

(9)

If the power supply cord of this appliance is damaged, it must be replaced by a repair shop designated by the

manufacturer, because special-purpose tools are required.

Control wiring

(A) Inter-unit

control wiring

(between outdoor

and indoor units)

(B) Remote control

wiring

(C) Control wiring

for group control

AWG #18

(0.75 mm

)

Use shielded wiring*

AWG #18

(0.75 mm

)

Use shielded wiring*

AWG #18

(0.75 mm

)

Use shielded wiring*

Max. 3,280 ft.

(Max. 1,000 m)

Max. 1,640 ft.

(Max. 500 m)

Max. 650 ft. (Total)

(Max. 200 m (Total))

SM830203-04.indb 97

15/10/16 10:44:49

Содержание U-26PE1U6










































































































































































































































































































Результаты поиска

Содержание U-26PE1U6

Отзывы:

Похожие инструкции для U-26PE1U6

Бренды по названию

Популярные бренды

Panasonic U-26PE1U6, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание U-26PE1U6

Отзывы:

Похожие инструкции для U-26PE1U6

Бренды по названию

Популярные бренды