Panasonic U-26PE1U6 Скачать руководство пользователя | Manualshive

Страница: 267 / 297

background image

5-7

5-6

5. Outdoor unit maintenance remote control

5-5. Monitoring the Outdoor Unit Alarm History: Display of Outdoor Unit Alarm History

* Displays outdoor unit alarms only. Does not display indoor unit alarms.
* Check the indoor unit alarm histories separately using the indoor unit remote

controllers or other control device.

<Operating procedure>

(1) Press and hold the button and button simultaneously for 4 seconds or longer

to change to outdoor unit alarm history mode.
During the alarm history display, “Service Check” is lit.
The display and operations are the same as the monitoring of the alarm device
history that is performed using the unit remote controller. However, the outdoor unit
address appears instead of the unit No.

(2) Press the

button and select the outdoor unit for alarm history monitoring.

(3) Use the temperature setting and buttons to select the item code for the alarm history.

The display shows the address of the selected outdoor unit, the item code, and the alarm history (alarm data).
The outdoor unit address is displayed as system XX-YY.
System XX = Outdoor unit system address

YY = Outdoor unit sub-bus address

The item code is displayed as 01– 08. 01 indicates the most recent alarm.
The alarm history is indicated by the alarm code. (If there have been no alarm codes, “

” is displayed.)

(4) To clear the alarm history, press the button. (The outdoor unit alarm history will be cleared.)

(5) To end, press the button. The display returns to the normal remote controller display.

5-6. Setting Modes: Setting the Outdoor Unit EEPROM

Setting mode 1

<Operating procedure>

(1) Press and hold the button and button simultaneously for 4 sec-

onds or longer.

(2) Use the temperature setting and buttons to change the item code.

The item codes and setting data are shown in the table on the next
page.

(3) Use the timer time and buttons to change the setting data.

To confirm the changed setting data, press the button.
(At this time, “Setting” stops blinking and remains lit.)

(4) During this mode, “Setting” is displayed, blinking. The outdoor unit

address display section displays “ALL,” the item code and number (DN
value in the table), and the setting data (6 digits).
(The setting data is displayed in 6 digits. The display changes between
the first 3 digits (Fig.

A

) and the last 3 digits (Fig.

B

).

When the first 3 digits are displayed, the top point of the colon is lit.)

(5) To end the setting mode, press the button.

(3)

(1)

(4)

(2)

(5)

are displayed alternately.

Display of first 3 digits

A

B

Display of last 3 digits

and

(Example shows display of 000 001.)

A

B

(3)

(1)

(2)

(5)

5

SM830203-04.indb 7

15/10/08 13:33:39

«
...
265
266
267
268
269
...
»

Содержание U-26PE1U6










































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для U-26PE1U6

Бренд: Olimpia splendid Страницы: 96

Бренд: Jaga Страницы: 12

Бренд: Daikin Страницы: 28

Бренд: Midea Страницы: 64

Бренд: EarthLinked Страницы: 11

Бренд: GE Страницы: 36

Бренд: Danby Страницы: 40

Бренд: Donaldson Torit Страницы: 52

Compact CWE Series

Бренд: Stulz Страницы: 28

Бренд: Payne Страницы: 6

Бренд: Rotenso Страницы: 68

Бренд: Haier Страницы: 60

Бренд: Haier Страницы: 52

AirStage AW A07L

Бренд: Fujitsu Страницы: 84

AIRSTAGE AUXS018GLEH

Бренд: Fujitsu Страницы: 14

Airstage AUXV004GLEH

Бренд: Fujitsu Страницы: 13

Бренд: Fujitsu Страницы: 209

Airstage UTP-RU01AH

Бренд: Fujitsu Страницы: 246

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды