Panasonic U-26PE1U6 страница 126 Скачать руководство пользователя | Manualshive

Страница: 126 / 297

background image

1-119

1-118

1. Specifications

CAUTION

To avoid gas from leaking
when removing the charge
hose, make sure the stem
of the gas tube is turned all
the way out (“BACK SEAT”)
position.

3. Charging Additional Refrigerant

Charging additional refrigerant (calculated from the

liquid tube length as shown in Section "1-13. Installation
Instructions, 1. Tubing Size, Table 1-4 Tubing Data for
Models", Amount of additional refrigerant charge) using
the liquid tube service valve. (Fig. 1-30)

Use a balance to measure the refrigerant accurately.

If the additional refrigerant charge amount cannot

be charged at once, charge the remaining
refrigerant in liquid form by using the gas tube
service valve with the system in Cooling mode at
the time of test run. (Fig. 1-31)
* If an additional refrigerant charge has been
performed, list the refrigerant tubing length and
amount of additional refrigerant charge on the
product label (inside the panel).

4. Finishing the Job

(1) With a hex wrench, turn the liquid tube service

valve stem counter-clockwise to fully open the
valve.

(2) Turn the gas tube service valve stem counter-clockwise

to fully open the valve.

(3) Loosen the charge hose connected to the gas

tube service port (5/16".) slightly to release the
pressure, then remove the hose.

(4) Replace the 5/16". fl are nut and its bonnet on the

gas tube service port and fasten the fl are nut
securely with an adjustable wrench or box wrench.
This process is very important to prevent gas from
leaking from the system.

(5) Replace the valve caps at both gas and liquid

service valves and fasten them securely.

Fig. 1-30

Fig. 1-31

Valve

Liquid

Manifold valve

Pressure
gauge

Lo

Hi

Outdoor unit

Liquid
tube

Gas
tube

Close

Close

Close

R410A

Outdoor unit

Liquid
tube

Gas
tube

Open

Open

Open

5. SELECTING THE INSTALLATION SITE

5-1. Indoor Unit
AVOID:

areas where leakage of flammable gas may be

expected.
places where large amounts of oil mist exist.
direct sunlight.
locations near inverter lamps which may affect the

performance of the unit.
locations near heat sources which may affect the

performance of the unit.
locations where external air may enter the room

directly. This may cause “sweating” on the air dis-

charge ports, causing them to spray or drip.
locations where the remote controller will be splashed

with water or affected by dampness or humidity.
installing the remote controller behind curtains or

furniture.

locations where the receiver in the indoor unit is

exposed to the inverter lamp light. Faulty operation

of the unit occurs.

DO:

select an appropriate position from which every

corner of the room can be uniformly cooled.
select a location where the ceiling is strong enough

to support the weight of the unit.
select a location where tubing and drain pipe have

the shortest run to the outdoor unit.

allow room for operation and maintenance as well as

unrestricted air flow around the unit.

If the indoor unit is installed on the ceiling where the

temperature or humidity inside is high (over 86°F(30°C)

/RH: 70%), add insulating material to the surface of the

unit to avoid dew condensation.

install the unit within the maximum elevation

difference above or below the outdoor unit and within

a total tubing length (L) from the outdoor unit as

detailed in the installation instructions packed with

the outdoor unit.
allow room for mounting the remote controller about

3 ft. off the floor, in an area that is not in direct

sunlight nor in the flow of cool air from the indoor

unit.

NOTE

Air delivery will be degraded if the distance from the
floor to the ceiling is greater than 10 ft.

Indoor Unit

locations where high-frequency emissions are

generated.

Ceiling (Type T1)

The rear of the indoor unit can be

installed flush against the wall.

Min. 2 ft.

Air intake

Min. 10 inch

Ceiling

Wall

NOTE

Min. 10 inch

Side view

Front view

Type F2

Ceiling

Wall Mounted (Type K1)

Min.

6 inch

Min.

12 inch

Min.

6 inch

Low Silhouette Ducted (Type F1)

4-Way Cassette (Type U1)

10 in.

10 in.

10 in.

3 ft.

3 ft.

3 ft.

3 ft.

3 ft.

Min.8 ft.

Shows Low Silhouette Ducted Type only

Air

discharge

9-27/32”

(250 mm)

25-19/32”

(650 mm)

Wall Mounted (Type K2)

The air inlet and outlet of the indoor unit must be free of any

obstructions to allow air to spread throughout the room.
1. The indoor unit must be within a maintenance soace.

Front View

min. 3" (7.5 cm) min.

2"

(5

cm)

min.

2"

(5

cm)

1

SM830203-04.indb 118

15/10/16 10:44:55

«
...
124
125
126
127
128
...
»

Содержание U-26PE1U6










































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для U-26PE1U6

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 11

Бренд: Panasonic Страницы: 8

Бренд: Panasonic Страницы: 24

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 19

BULKHEAD BRE-026BS

Бренд: ActronAir Страницы: 24

Бренд: Dometic Страницы: 2

Air scat RF-17F series

Бренд: Fuji Electric Страницы: 30

Бренд: E-Tac Страницы: 24

MPN2-12ERN1-BH2

Бренд: Uberhaus Страницы: 27

Бренд: Bionaire Страницы: 2

Бренд: Rotenso Страницы: 16

Бренд: Klimaire Страницы: 82

Бренд: Lennox Страницы: 32

AirMedic Pro 5 HD

Бренд: AllerAir Страницы: 2

Бренд: Breezair Страницы: 20

Бренд: Daikin Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды