manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Руководство по эксплуатации

Panasonic Switch-M8ePWR PN27089KA - функциональный переключатель с возможностью управления нагрузками. Для более подробной информации об использовании устройства, скачайте бесплатно Operation Manual на manualshive.com. Получите полное руководство по эксплуатации, чтобы настроить и использовать ваш продукт наилучшим образом.

Поделиться
Скачать
background image

 

 

177 

Screen Description 

Entry 

Displays the event number. 

Time 

Displays the time when the event occurred, or the time accumulated after boot 
if the clock is not set. 

Event 
 

 

Displays the description of the event caused to the Switching Hub. 
Login from console 

Indicates a login from the console. 

Login failed from 
console 

Indicates a login authentication failure from the 
console. 

Login from telnet <IP: 
xxx.xxx.xxx.xxx> 

Indicates a login from the host with IP address 
xxx.xxx.xxx.xxx via Telnet. 

Login from SSH <IP: 
xxx.xxx.xxx.xxx> 

Indicates a login from the host with IP address 
xxx.xxx.xxx.xxx via SSH. 

Login failed from telnet 
<IP: xxx.xxx.xxx.xxx> 

Indicates a login authentication failure from the host 
with IP address xxx.xxx.xxx.xxx via Telnet. 

Login failed from SSH 
<IP: xxx.xxx.xxx.xxx> 

Indicates a login authentication failure from the host 
with IP address xxx.xxx.xxx.xxx via SSH. 

Reboot: Normal 

Indicates that this Switching Hub rebooted. 

Reboot: Factory Default  Indicates that this Switching Hub rebooted to return 

settings to factory default. 

Reboot: Factory Default 
Except IP 

Indicates that this Switching Hub rebooted to return 
settings except the IP address to factory default. 

Reboot: Exception.. 

Indicates that this Switching Hub rebooted due to an 
exception handling. 

Configuration changed 

Indicates that the configuration was changed. 

Switch start 

Indicates that this Switching Hub booted. 

Runtime changes from 
xxx.xxx.xxx.xxx 

Indicates that firmware was downloaded from IP 
xxx.xxx.xxx.xxx and updated. 

Configuration file 
uploaded 

Indicates that the configuration file was uploaded 
via TFTP. 

Configuration file 
downloaded 

Indicates that the configuration file was downloaded 
via TFTP. 

Port-xx link-down 

Indicates that Port xx was linked down. 

Port-xx link-up 

Indicates that Port xx was linked up. 

Enter Command Line 
Interface 

Indicates that the user moved from the configuration 
menu to CLI (Command Line Interface). 

xx:xx:xx:xx:xx:xx was 
authorized at port xx. 

Indicates that IEEE802.1X authentication succeeded 
on Port xx from the terminal with xx:xx:xx:xx:xx:xx. 

xx:xx:xx:xx:xx:xx was 
rejected at port xx. 

Indicates that IEEE802.1X authentication failed on 
Port xx from the terminal with xx:xx:xx:xx:xx:xx. 

Authentication failure 

Indicates that an unauthorized manager accessed by 
SNMP. 

Port-xx Power ON 
notification 

Indicates that the PoE power supply to Port xx is 
turned on. 

Port-xx Power OFF 
notification 

Indicates that the PoE power supply to Port xx is 
turned off. 

Содержание Switch-M8ePWR PN27089KA



































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Switch-M8ePWR PN27089KA

D-Link DI-634M Quick Installation Manual preview
DI-634M
Бренд: D-Link Страницы: 12
Lab.gruppen NLB 60E Operation Manual preview
NLB 60E
Бренд: Lab.gruppen Страницы: 35
Tandberg Data RDX QuikStation 4 Quick Start Manuals preview
RDX QuikStation 4
Бренд: Tandberg Data Страницы: 2
AlphaShield INTERNET PRIVACY PROTECTION (Spanish) Manual Del Usuario preview
INTERNET PRIVACY PROTECTION
Бренд: AlphaShield Страницы: 49
ZyXEL Communications ZyXEL EES-1024AF User Manual preview
ZyXEL EES-1024AF
Бренд: ZyXEL Communications Страницы: 99
Google AC-1304 User Manual preview
AC-1304
Бренд: Google Страницы: 14
H3C S12500R-2L Installation, Quick Start preview
S12500R-2L
Бренд: H3C Страницы: 26
XtendLan NVR-xUD User Manual preview
NVR-xUD
Бренд: XtendLan Страницы: 228
TP-Link TL-MR3220 Quick Installation Manual preview
TL-MR3220
Бренд: TP-Link Страницы: 87
Ubiquiti UniFi WiFi BaseStation XG Quick Start Manual preview
UniFi WiFi BaseStation XG
Бренд: Ubiquiti Страницы: 19
CG Emotron OSTO 100 Instruction Manual preview
Emotron OSTO 100
Бренд: CG Страницы: 112
AIC SB401-MN User Manual preview
SB401-MN
Бренд: AIC Страницы: 88
Modecom MC-421 Quick Installation Manual preview
MC-421
Бренд: Modecom Страницы: 16
Buffalo LinkStation 500 User Manual preview
LinkStation 500
Бренд: Buffalo Страницы: 139
NetComm 4GM3W User Manual preview
4GM3W
Бренд: NetComm Страницы: 65
PairGain 150-2230-01 Quick Installation Manual preview
150-2230-01
Бренд: PairGain Страницы: 48
IBM Nways 2216 Service And Maintenance Manual preview
Nways 2216
Бренд: IBM Страницы: 168
Clas Ohlson AE222X1 Quick Start Manual preview
AE222X1
Бренд: Clas Ohlson Страницы: 4

Бренды по названию

Популярные бренды

Загрузить еще бренды