manualshive.com logo in svg

Panasonic Switch-M8ePWR PN27089KA, Руководство по эксплуатации, Страница: 120 / 194

Поделиться
Скачать
Panasonic Switch-M8ePWR PN27089KA Скачать руководство пользователя страница 120

 

 

120 

Available commands are listed below. 

S  Switch enabled/disabled of the QoS function. 

 

Press"S" to change the command prompt to "Enable or Disable QoS (E/D)>." 
To enable the QoS function, press "E." To disable it, press "D." 

M  Assign priority (Traffic Class) to a priority value of IEEE802.1p. 

 

Press "M" to change the command prompt to "Enter Priority (E/D)>." Enter a priority 
value (0 to 7) to be assigned. Then, the command prompt changes to "Enter traffic 
class for priority #>." Enter Traffic Class (0 to 3). 

C  Move to the screen for configuring a scheduling method. 

 

Press "C" to change the screen to Scheduling Method. Refer to the section 4.7.5.b for 
how to set.

 

Q  Return to the previous menu. 

Содержание Switch-M8ePWR PN27089KA



































































































































































































Отзывы:

Нет отзывов