Panasonic Switch-M8ePWR PN27089KA Скачать руководство пользователя | Manualshive

Страница: 175 / 194

background image

175

Available commands are listed below.

I

Set the IP address of the target of the ping.

Press "I." The command prompt changes to "Enter new Target IP Address >." Enter
the IP address.

N Set the number of times of ping.

Press "N." The command prompt changes to "Enter new Request Times >." Enter the
number of times between 1 and 10.

T Set the time before timeout occurs.

Press "T." The command prompt changes to "Enter new Timeout Value >." Set the
time between 1 to 5 seconds.

E Execute the ping command. Or, clear the display.

Press "E." The command prompt changes to "Execute Ping or Clean before Ping Data
(E/C)>." Press "E" to execute ping. Press "C" to only clear the display.

S Cancel the ping command.

Press "S" or "Ctrl+C" during the ping execution to cancel it.

Q Return to the previous menu.

Fig. 4-9-8 Display during ping execution

PN27089K/PN27089KA Local Management System

Switch Tools Configuration -> Ping Execution

Target IP Address:     192.168.1.2
Number of Requests:    10
Timeout Value:         3 Sec.
=============== Result ===============
    No. 1                  14 ms
    No. 2                  9 ms
    No. 3                  7 ms
    No. 4                  7 ms
    Waiting for response...

-------------------------------- <COMMAND> -----------------------------------
Set Target [I]P Address                [E]xecute Ping
Set [N]umber of Requests               [S]top Ping
Set [T]imeout Value                    [Q]uit to previous menu

S or Ctrl-C Stop ping function

«
...
173
174
175
176
177
...
»

Содержание Switch-M8ePWR PN27089KA



































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Switch-M8ePWR PN27089KA

Бренд: Ubiquiti Страницы: 24

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 40

ShareCenter Quattro DNS-345

Бренд: D-Link Страницы: 4

ShareCenter DNS-343

Бренд: D-Link Страницы: 12

AirPlus G DWL-G710

Бренд: D-Link Страницы: 5

MYDLINK DNR-322L

Бренд: D-Link Страницы: 4

mydlink DNR-312L

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 16

Бренд: D-Link Страницы: 88

Бренд: Rain Bird Страницы: 17

Бренд: Dahua Страницы: 24

Бренд: LORD Страницы: 9

ADSL 2/2+ Router with USB Port ADE-3410v2

Бренд: Planet Страницы: 62

Бренд: Conceptronic Страницы: 2

Бренд: FS Страницы: 19

Parallel & Serial Port Checker PPC

Бренд: B&B Electronics Страницы: 4

SmartNode 4520 Series

Бренд: Patton electronics Страницы: 90

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды